IFM SM4x00 Скачать руководство пользователя страница 5

Страница: 5 / 37

►

Install the units according to the applicable rules and regulations�

►

Ensure that the system is free of pressure during installation�

►

Protect the housing against contact with flammable substances and uninten-

tional contact� To do so, equip the units with suitable protection (e�g� protective

cover)�

►

Do not press the pushbuttons manually� instead use another object (e�g�

ballpoint pen)�

3 Functions and features

The unit monitors liquid media� It detects the 3 process categories volumetric flow,

consumed quantity, medium temperature�

Pressure Equipment Directive (PED)

The units comply with the Pressure Equipment Directive and are designed and

manufactured for group 2 fluids in accordance with the sound engineering prac-

tice� Use of group 1 fluids on request�

Application area

Conductive liquids with the following properties:
•

Conductivity: ≥ 20 µS/cm

• Viscosity: < 70 mm

/s at 40 °C; < 70 cSt at 104 °F

4 Function

• The unit detects the flow based on the magnetic-inductive volumetric flow

measuring principle�

•  The unit also detects the medium temperature�
•  It features an IO-Link interface�
•  The unit displays the current process value�

Содержание SM4x00






































Результаты поиска

Содержание SM4x00

Отзывы:

Похожие инструкции для SM4x00

Бренды по названию

Популярные бренды

IFM SM4x00, Руководство по эксплуатации

Результаты поиска

Содержание SM4x00

Отзывы:

Похожие инструкции для SM4x00

Бренды по названию

Популярные бренды