IFM SDG070 Скачать руководство пользователя страница 20

Страница: 20 / 21

10.5.7 Low flow cut-off

►

Select [LFC] and set the limit�

10.6 Service functions
10.6.1 Read min/max values

Read minimum or maximum measured values:

►

Select HI or LO

HI = maximum volumetric flow, LO = minimum volumetric flow

Delete memory:

►

Select HI or LO�

►

Press and hold [Set] until [----] is displayed�

►

Briefly press [Mode/Enter]�

It makes sense to delete the memories as soon as the unit operates under normal

operating conditions for the first time�

10.6.2 Restoring the factory settings

►

Select [rES]�

►

Press and hold [Set] until [----] is displayed�

►

Briefly press [Mode/Enter]�

11 Operation

Correct operation and compliance with the measurement accuracy can only be en-

sured if the environmental conditions specified in the "Technical data" are adhered

to� Ensure that the maximum pressure range, measuring range and permitted

operating temperature are not exceeded�

After power on and expiry of the power-on delay time (approx� 0�5 s) the unit is in

the Run mode (= normal operating mode)� It carries out its measurement and eval-

uation functions and generates output signals according to the set parameters�

• Operating indications

→ 8 Operating and display elements

�

• During the power-on delay time the outputs are switched as programmed: ON

for NO function (Hno / Fno), OFF for NC function (Hnc / Fnc)�

• If output 2 is configured as analogue output, the output signal is at the final

value of the measuring range during the power-on delay time�

11.1 Reading of the set parameters

►

Press [Mode/Enter] until the requested parameter is displayed�

Содержание SDG070






















Результаты поиска

Содержание SDG070

Отзывы:

Бренды по названию

Популярные бренды

IFM SDG070, Руководство по эксплуатации

Результаты поиска

Содержание SDG070

Отзывы:

Бренды по названию

Популярные бренды