IFM SDG070 Скачать руководство пользователя страница 14

Страница: 14 / 21

Explanation of the menu

ImPS

Pulse value (consumed quantity at which 1 pulse is delivered)

ImPR

Configuration of the output for consumed quantity monitoring:

YES (pulse signal), no (switching signal)

SP1 / rP1

Upper / lower limit value for the volumetric flow at which OUT1 switches

OU1

Output function for OUT1 (volumetric flow):

-Hno, Hnc, Fno, Fnc: switching signal for the limits

-ImP: consumed quantity monitoring (totaliser function)

OU2

Output function for OUT2 (volumetric flow or temperature):

-Hno, Hnc, Fno, Fnc: switching signal for the limits

-I (current signal 4��20 mA)

Input function for OUT2:

-In�D: input for external meter reset signal

SP2 / rP2

Upper / lower limit value at which OUT2 switches�

ASP / AEP

Analogue start point / analogue end point for volumetric flow or

temperature on OUT2

DIn2

Configuration of the input for external meter reset signal:

HIGH, +EDG, LOW, -EDG

Extended functions / opening of menu level 2

HI / LO Maximum / minimum value memory for volumetric flow

FOU1 / FOU2 Behaviour of OUT1 / OUT2 in case of an internal fault:

OU, On, OFF

dAP Measured value damping: damping constant in seconds

rTo Counter reset: manual reset / time-controlled reset

diS Update rate and orientation of the display

Uni Standard unit of measurement for volumetric flow: Nl/min, Nm

/h, Nm/s

SELd Standard measured variable of the display: FLOW (volumetric flow value),

TEMP (medium temperature), TOTL (meter reading)

SEL2 Standard unit of measurement for evaluation by OUT2:

FLOW (volumetric flow) or TEMP (temperature)

rEF�P Standard pressure to which the measured and display values for volumet-

ric flow refer

rEF�T Standard temperature to which the measured and display values for

volumetric flow refer

LFC Low flow cut-off

rES Restoring the factory settings

Содержание SDG070






















Результаты поиска

Содержание SDG070

Отзывы:

Похожие инструкции для SDG070

Бренды по названию

Популярные бренды

IFM SDG070, Руководство по эксплуатации

Результаты поиска

Содержание SDG070

Отзывы:

Похожие инструкции для SDG070

Бренды по названию

Популярные бренды