IFM SDG070 Скачать руководство пользователя

Страница: 19 / 21

10.5.2 Standard display

►

Select [SELd] and define the standard unit of measurement

FLOW = display shows the current volumetric flow value in the standard unit of meas-

urement�

TOTL = display shows the current meter reading in the unit providing the highest ac-

curacy�

TEMP = the current medium temperature in °C is displayed�

►

Select [diS] and set the update rate and orientation of the display:

d1 = update of the measured values every 50 ms�

d2 = update of the measured values every 200 ms�

d3 = update of the measured values every 600 ms�

rd1, rd2, rd3 = display like d1, d2, d3; rotated by 180�

OFF = the display is switched off in the operating mode� The LEDs remain active

even if the display is deactivated� Error messages are displayed even if the display is

deactivated�

10.5.3 Measured value damping

► Select [dAP] and set the damping constant in seconds (τ value 63 %).

10.5.4 Error behaviour of the outputs

►

Select [FOU1] and set the value:

-On = Output 1 switches ON in case of a fault�

-OFF = Output 1 switches OFF in case of an error�

-OU = Output 1 switches irrespective of the fault as defined with the parameters�

►

Select [FOU2] and set the value:

1� Switching output:

-On = Output 2 switches ON in case of a fault�

-OFF = Output 2 switches OFF in case of a fault�

-OU = Output 2 switches irrespective of the fault as defined with the parameters�

2� Analogue output:

-On = The analogue signal goes to the upper fault value�

OFF = The analogue value goes to the lower fault value�

OU = The analogue signal corresponds to the measured value�

10.5.5 Setting of the standard pressure

►

Select [rEF�P] and set the requested standard pressure�

10.5.6 Setting of the standard temperature

►

Select [rEF�T] and set the requested standard temperature�

Содержание SDG070






















Результаты поиска

Содержание SDG070

Отзывы:

Похожие инструкции для SDG070

Бренды по названию

Популярные бренды

IFM SDG070, Руководство по эксплуатации

Результаты поиска

Содержание SDG070

Отзывы:

Похожие инструкции для SDG070

Бренды по названию

Популярные бренды