IFM PI16 Series Скачать руководство пользователя | Manualshive

Страница: 6 / 35

background image

PI16xx PI18xx

Electronic pressure sensor

6

3 Intended use

The device measures and monitors the system pressure or the hydrostatic level and the temperature
in systems.

3.1 Application area

Type of pressure: relative pressure

Information on pressure rating and bursting pressure

Ò

Data sheet

Avoid static and dynamic overpressure exceeding the indicated pressure rating by taking
appropriate measures. The indicated bursting pressure must not be exceeded. Even if the
bursting pressure is exceeded only for a short time, the unit may be destroyed. ATTENTION:
Risk of injury!

Not suitable for systems that have to meet the criteria of E9.2 / 63-04 of the 3-A standard 63-04.

The units are vacuum resistant. Adhere to the specifications in the data sheet!

«
...
4
5
6
7
8
...
»

Содержание PI16 Series




































Отзывы:

Нет отзывов

Похожие инструкции для PI16 Series

Бренд: GE Страницы: 20

Бренд: GE Страницы: 2

Бренд: Hama Страницы: 40

Бренд: Rave Sports Страницы: 16

StudSensor HD25

Бренд: Zircon Страницы: 2

Бренд: Anslut Страницы: 12

Бренд: Metra Electronics Страницы: 2

Бренд: Southern Enterprises Страницы: 4

Бренд: Ohlins Страницы: 8

Бренд: hepco & becker Страницы: 4

Бренд: Leisure Concepts Страницы: 2

BLADE-AL(TB)-TL2

Бренд: iDataLink Страницы: 9

Бренд: Leclerc Страницы: 8

Бренд: MAXXMEE Страницы: 40

Бренд: Perma Страницы: 12

Бренд: Trane Страницы: 17

Бренд: Magneti Marelli Страницы: 2

Бренд: hepco & becker Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды