background image

Electronic pressure sensor

PI16xx PI18xx

27

u

Select [diS] and set the update rate and orientation of the display:

• [d1]: update of the measured values every 50 ms.

• [d2]: update of the measured values every 200 ms.

• [d3]: update of the measured values every 600 ms.

• [rd1], [rd2], [rd3]: display as with d1, d2, d3; rotated by 180°.

• [OFF] = The measured value display is deactivated in the Run mode.

When one of the buttons is pressed, the current measured value is displayed for 30 s. Pressing the
[Enter] button again activates the display mode. The LEDs remain active even if the display is deacti-
vated. Error messages are displayed even if the display is deactivated.

[diS]

10.3 Set output signals

10.3.1 Setting of the output function

u

Select [OU1] and set the switching function:

• [Hno] = hysteresis function/normally open.

• [Hnc] = hysteresis function/normally closed.

• [Fno] = window function/normally open.

• [Fnc] = window function/normally closed

• [Off] = output off.

[OU1]

u

Select [OU2] and set the function:

• [Hno] = hysteresis function/normally open.

• [Hnc] = hysteresis function/normally closed.

• [Fno] = window function/normally open.

• [Fnc] = window function/normally closed

• [I] = current signal proportional to pressure 4…20 mA.

• [InEG] = current signal proportional to pressure 20…4 mA.

• [Off] = output off.

[OU2]

10.3.2 Set switching limits

u

Select [SP1] / [SP2] and set the value at which the output switches.

[SP1]

[SP2]

u

Select [rP1] / [rP2] and set the value at which the output switches.

rPx is always smaller than SPx. The unit only accepts values which are lower than the value for SPx.

[rP1]

[rP2]

10.3.3 Define switching limits for the window function

u

[ou1] /[ou2] must be set as [Fno] or [Fnc].

u

Select [FHx] and set the upper limit.

[FH1]

[FH2]

u

Select [FLx] and set the lower limit.

FLx is always lower than FHx. The unit only accepts values which are lower than the value for FHx.

[FL1]

[FL2]

10.3.4 Scale analogue value for OUT2

u

Approach the desired minimum system pressure in the installation and keep it constant.

u

Select [tASP] with [Enter].

u

Press [▲] or [▼] until [----] is displayed.

u

Confirm [----] with [Enter].

w

The current pressure is defined as start value for the analogue signal.

[tASP]

Содержание PI16 Series




































Отзывы: