IFM Electronic Ecomat 100 CR2014 Скачать руководство пользователя страница 3

Страница: 3 / 27

CabinetModule CR2014

Safety instructions

Notes on this manual

1.1
This manual is part of the device. It contains information and illustrations

about the correct handling of the device and must be read before installation

or use.

Observe the operating instructions� Non-observance of the notes, operation which

is not in accordance with the intended use, wrong installation or handling can

result in serious harm concerning the safety of persons and plant�
These instructions are intended for “authorised” persons according to the EMC

and low-voltage directives�

Notes on the device

1.2

The device must only be installed, connected and put into operation by a qualified

electrician�
Disconnect the device externally before handling it� If necessary, also disconnect

any independently supplied output load circuits�
If the device is not supplied by the mobile on-board system (12/24 V battery

operation), it must be ensured that the external voltage is generated and supplied

according to the criteria for safety extra-low voltage (SELV) as this voltage is

supplied without further measures to the connected controller, the sensors and the

actuators�
The wiring of all signals in connection with the SELV circuit of the device must also

comply with the SELV criteria (safety extra-low voltage, safe electrical separation

from other electric circuits)� If the supplied SELV voltage is externally grounded

(SELV becomes PELV), the responsibility lies with the user and the respective

national installation regulations must be complied with� All statements in this

manual refer to the device the SELV voltage of which is not grounded�
The connection terminals may only be supplied with the signals indicated in the

technical data and/or on the device label and only the approved accessories of ifm

electronic may be connected�
According to the technical specifications below the device can be operated in

a wide operating temperature range� Because of the additional internal heating

the housing walls can have high perceptible temperatures when touched in hot

environments�
In case of malfunctions or uncertainties please contact the manufacturer�

Tampering with the device can lead to serious risks for the safety of persons and

plant� It is not permitted and leads to the exclusion of any liability and warranty

claims�

Содержание Ecomat 100 CR2014




























Результаты поиска

Содержание Ecomat 100 CR2014

Отзывы:

Похожие инструкции для Ecomat 100 CR2014

Бренды по названию

Популярные бренды

IFM Electronic Ecomat 100 CR2014, Руководство по эксплуатации устройства

Результаты поиска

Содержание Ecomat 100 CR2014

Отзывы:

Похожие инструкции для Ecomat 100 CR2014

Бренды по названию

Популярные бренды