IEI Technology DM series Скачать руководство пользователя страница 97

Страница: 97 / 128

DM Series Monitor

Page 83

USB Interface:

If the touch screen interface connection is a USB connection,

connect the USB connector on the single board computer to the external USB

port connector of the DM Series monitor.

7.3 Touch Panel Driver Installation

WARNING:

Before the touch screen driver is installed, make sure the system is

connected to the monitor with a USB cable or an RS-232 null cable.

Also, make sure the VGA connector on the system is connected to the

VGA connector on the bottom of the monitor.

To install the touch panel driver for the DM Series, please follow the instructions below:

Step 1:

Connect the DM Series monitor to the single board computer

. See above.

Step 2:

Install the driver CD

. Install the driver CD into the system to which the DM

Series monitor is connected.

Step 3:

Select the

Touch Screen

option in the menu of driver CD. The directory in

Figure 7-1

appears.

Figure 7-1: Setup Icon

Содержание DM series

































































































































Результаты поиска

Содержание DM series

Отзывы:

IEI Technology DM series, Руководство пользователя, Страница: 97 / 128

Результаты поиска

Содержание DM series

Отзывы: