manualshive.com logo in svg

IEI Technology DM series, Руководство пользователя, Страница: 92 / 128

Поделиться
Скачать
IEI Technology DM series Скачать руководство пользователя страница 92

 

 

DM Series Monitor

Page 78 

6.2 Using the OSD 

OSD menu options are described below. 

6.2.1 Main Display Features 

Main display features are shown in 

Figure 6-3

. 

 

Figure 6-3: Main Display Features 

 

Brightness  

The brightness option adjusts the brightness of screen. This function 

adjusts the offset value of ADC. Setting this value too high or too low 

will affect the quality of image. When the auto- dimming function is 

turned on, the brightness control is not effective.   

Contrast  

This function adjusts the gain value of ADC. Adjusting this value too 

high or too low will worsen the quality of image. 

Clock 

Adjusts the width of the display screen. 

Phase 

Adjusts the input signal.   

H. Position 

Adjusts the horizontal position of the display screen. 

V. Position 

Adjusts the vertical position of the display screen 

Sharpness 

Adjust the sharpness of the display 

 

Содержание DM series

































































































































Отзывы:

Нет отзывов