manualshive.com logo in svg

IEI Technology DM series, Руководство пользователя, Страница: 2 / 128

Поделиться
Скачать
IEI Technology DM series Скачать руководство пользователя страница 2

 

 

DM Series Monitor

Page II 

Revision 

Date Version 

Changes 

5 May, 2011 

2.04 

Added panel opening dimensions in Section 5.5.1 

23 February, 2011 

2.03 

Minor changes 

29 December, 2010 

2.02 

Updated Chapter 7 Software Drivers 

09 December, 2010 

2.01 

Modified AV-6600 AD board information. 

Updated Chapter 6 OSD Controls section 

15 June, 2010 

2.00 

Updated for DM-xx-R20 series 

16 July, 2009 

1.14 

Updated “Chapter 

2

6: OSD Controls”

 

April, 2008 

1.13 

Added DM-121GX models information 

Added DM-190 rack mount installation 

Added the smartOSD appendix 

July, 2007 

1.12 

Cautions for VESA mounting kit are added in p46, p140

 

May, 2007 

1.11 

AV-6600 AD Board CN25 connector pin 3 voltage changed to 

+9V~+36V input 

April, 2007 

1.10 

Updated Figure 1-3 and Section 4.4 for AV-6600 AD Board V2.0

March, 2007 

1.01 

Correct Figure 4-14 labeling   

Revised CN7 connector as 12V power 

Revised CN7 connector as 12V power; added connector pinouts

Correct LVDS connector label 

July, 2006 

1.00 

Initial Release 

 

Содержание DM series

































































































































Отзывы:

Нет отзывов