IEI Technology DM series Скачать руководство пользователя страница 62

Страница: 62 / 128

DM Series Monitor

Page 48

5.2.3 Packing List

All the monitors in the DM series are shipped with the following components:

1 x DM-190/170/150/121/104/84/65 series LCD monitor.

1 x AC power cable

1 x VGA cable

1 x 50W AC power adapter (DM-190 / 170 / 150)

1 x 36W AC power adapter (DM-121/ 104 / 84 / 65)

5 x Replacement round head screw

5 x Replacement flat head screw

5 x Replacement wire strain band

1 x User manual on CDROM

1 x Touch panel RS-232 cable

1 x Touch panel USB cable

1 x Touch Pen

1 x Driver CDROM

1 x Power cable for terminal block (Optional for M model)

If any of these items are missing or damaged, contact the distributor or sales

representative immediately.

5.3 Pre-installation Preparation

5.3.1 Tools

Before installing the DM series LCD monitor, make sure the following tools are on hand:

Philips (crosshead) screwdriver

: All the retention screws on the system are

Philips screws.

Soft working mat

: When the DM series LCD monitor is installed, the screen

is placed on the working surface. It is therefore important to rest the MPC

indutrial workstation on a soft at that cannot damage the LCD screen on the

front of the DM series LCD monitor.

Содержание DM series

































































































































Результаты поиска

Содержание DM series

Отзывы:

IEI Technology DM series, Руководство пользователя, Страница: 62 / 128

Результаты поиска

Содержание DM series

Отзывы: