manualshive.com logo in svg

IEI Technology DM series, Руководство пользователя, Страница: 80 / 128

Поделиться
Скачать
IEI Technology DM series Скачать руководство пользователя страница 80

 

 

DM Series Monitor

Page 66 

 

Step 3: 

Carefully insert the slotted holes of the brackets on the monitor through the bolts 

on the rack and gently pull the monitor downwards until the bolts rests securely 

in the slotted holes. (See 

5

Figure 5-22

). Ensure that all six of the bolts fit snuggly 

into their respective slotted holes. 

 

Figure 5-22: Rack Mounting (DM-190) 

 

5.5.2.3 DM-84 and DM-65 Cabinet and Rack Installation 

Use the standard panel mounting procedure (

Section 

5

5.5.1.1

) to mount the DM-84 

monitor into a cabinet/rack and use the DM-65 panel mounting procedure (

Section 

5

5.5.1.2

) 

to mount the DM-65 monitor into a cabinet/rack. 

5.5.3 DIN Rail Installation 

The DM-84 and DM-65 have four holes located on the rear panel for mounting the monitor 

to a DIN rail clamp. To mount the DM series LCD monitor onto a DIN rail, please follow the 

steps below. 

Содержание DM series

































































































































Отзывы:

Нет отзывов