IEI Technology DM series Скачать руководство пользователя страница 107

Страница: 107 / 128

DM Series Monitor

Page 93

A.1.2 Anti-static Precautions

WARNING:

Failure to take ESD precautions during the installation of the DM Series

may result in permanent damage to the DM Series and severe injury to

the user.

Electrostatic discharge (ESD) can cause serious damage to electronic components,

including the DM Series. Dry climates are especially susceptible to ESD. It is therefore

critical that whenever the DM Series is opened and any of the electrical components are

handled, the following anti-static precautions are strictly adhered to.

Wear an anti-static wristband

: Wearing a simple anti-static wristband can

help to prevent ESD from damaging any electrical component.

Self-grounding

: Before handling any electrical component, touch any

grounded conducting material. During the time the electrical component is

handled, frequently touch any conducting materials that are connected to the

ground.

Use an anti-static pad

: When configuring or working with an electrical

component, place it on an antic-static pad. This reduces the possibility of ESD

damage.

Only handle the edges of the electrical component

: When handling the

electrical component, hold the electrical component by its edges.

A.2 Maintenance and Cleaning Precautions

When maintaining or cleaning the DM Series, please follow the guidelines below.

A.2.1 Maintenance and Cleaning

Prior to cleaning any part or component of the DM Series, please read the details below.

Except for the LCD panel, never spray or squirt liquids directly onto any other

components. To clean the LCD panel, gently wipe it with a piece of soft dry

cloth or a slightly moistened cloth.

Содержание DM series

































































































































Результаты поиска

Содержание DM series

Отзывы:

IEI Technology DM series, Руководство пользователя, Страница: 107 / 128

Результаты поиска

Содержание DM series

Отзывы: