IEI Technology DM series Скачать руководство пользователя страница 100

Страница: 100 / 128

DM Series Monitor

Page 86

Figure 7-6: Finish Installation

7.4 Change the Touch Screen Interface

If the touch screen interface must be changed from an RS-232 interface to a USB

interface or, from a USB interface to an RS-232 interface, the following steps must be

followed.

Step 1:

Uninstall the touch screen driver

Step 2:

Remove the interface cable i.e. remove the RS-232 cable or the USB cable

Step 3:

Install the new cable i.e. install the USB cable or the RS-232 cable.

Step 4:

Reinstall the driver CD as described above.

Step 0:

7.5 Calibrating the Touch Screen

To calibrate the touch screen cursor with the motion of the touch screen pen (or finger),

please follow the steps below:

Step 1:

Make sure the system is properly connected through an RS-232 or a USB

interface to the DM Series monitor.

Step 2:

Make sure the touch screen driver is properly installed.

Содержание DM series

































































































































Результаты поиска

Содержание DM series

Отзывы:

IEI Technology DM series, Руководство пользователя, Страница: 100 / 128

Результаты поиска

Содержание DM series

Отзывы: