IDTECK Star iCON100 Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 24

background image

※

iCON100/iCON100-SR QUICK INSTALLATION GUIDE

17

6.2 RS-422 Communication Port Connection

6.2.1 RS-422 Connection (Single iCON100 Connection)

An RS422/RS232 converter is required to use RS422 communication between the

iCON100

and the PC.

CAUTION:

The INC400 converter is recommended for stable communication when the distance between

the converter and the device is too far.

Please follow the instructions below;

- Connect RS422-TX (+) (Gray wire) of iCON100 to RS422-RX (+) port of converter.
- Connect RS422-TX (-) (Yellow wire) of iCON100 to RS422-RX (-) port of converter.
- Connect RS422-RX (+) (Brown wire) of iCON100 to RS422-TX (+) port of converter.
- Connect RS422-RX (-) (Blue wire) of iCON100 to RS422-TX (-) port of converter.

- Plug in the RS232 9PIN connector of the converter to the COM n port of the PC.
- Install and run iCON100 Application Software.

Figure: RS422 Communication between

iCON100

and the PC

«
...
15
16
17
18
19
...
»

Содержание Star iCON100

























Отзывы:

Нет отзывов

Похожие инструкции для Star iCON100

Бренд: Panasonic Страницы: 72

Бренд: Panasonic Страницы: 45

Бренд: Panasonic Страницы: 24

Бренд: YASKAWA Страницы: 256

Бренд: Baccara Страницы: 16

Бренд: Gate Motors Страницы: 6

Бренд: Jandy Страницы: 28

Бренд: Jands Страницы: 6

GECO LUX GECO60

Бренд: GiBiDi Страницы: 48

Бренд: CORNING Страницы: 12

Waukesha Cherry-Burrell D4 Series

Бренд: SPX FLOW Страницы: 34

OPTISWITCH 5100 C

Бренд: KROHNE Страницы: 40

Бренд: Danfoss Страницы: 10

Бренд: SimCom Страницы: 13

Бренд: Calex Страницы: 16

Бренд: Etherma Страницы: 8

KaDe KDH-KZ620U

Бренд: AAT Holding Страницы: 28

Бренд: Pulse Shower Spas Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды