FDX-08 User Guide
95
Item
Description
Optic scan converter output board
(*11)
Output
2 outputs (*17)
Video
Digital optical signal for
extension
Digital optical signal for extension (*12)
HDCP 1.4
Formats
VGA / SVGA / XGA / WXGA (1280x768) / WXGA (1280x800) / Quad-VGA / SXGA / WXGA (1360x768) /
WXGA (1366x768) / SXGA+ / WXGA+ / WXGA++ / UXGA / WSXGA+ / VESAHD / WUXGA
* VESAHD / WUXGA are output as Reduced Blanking.
480p / 576p / 720p / 1080i / 1080p (*19)
Audio
Digital optical signal for
extension
Multi-channel LPCM up to 8 channels
Sampling frequency: 32 kHz to 192 kHz, Sample size: 16 bit to 24 bit
Cable
Duplex fiber cable, SFP module (2 LC connectors) (*13)
Polishing (*14)
SFP for Multimode : PC (recommended)
SFP for Singlemode: UPC (recommended), SPC supported *APC is not supported
Transmission distances (*15)
Multimode fiber (OM3): Up to 984 ft. (300 m)
Multimode fiber (OM4): Up to 0.62 mi. (1 km)
Singlemode fiber (OS1) : Up to 2.92 mi. (4.7 km)
Singlemode fiber (OS1) : Up to 6.21 mi. (10 km) (Optional)
*1
Seamless switching with a black frame.
*2
The anti-snow feature automatically fixes snow noise that is a specific symptom of HDCP-compliant signals and mainly occurs at start-up. This feature does not work when
snow noise has already occurred during startup or when it occurs due to a bad condition of the transmission line.
*3
For digital systems, some problems, such as an HDCP authentication error, can often be recovered by physically disconnecting and reconnecting the digital cables. However,
the Connection Reset feature will fix these problems automatically without the need to physically plug and unplug the cables. It creates the same condition as if the cable were
physically disconnected and reconnected. This feature only works for the FDX’s output. If other devices are connected between the FDX’s output and sink device, this feature
may be invalid.
*4
Please contact our Sales Division for power consumption information of each configuration.
*5
36 bit/pixel (12 bit/component) Deep Color is supported while x.v.Color, 3D, ARC, HEC, and CEC are not supported.
*6
The maximum cable distance varies depending on the connected devices and was measured under following conditions:
・
IDK’s AWG 24 cable was used and 1080p@60 24 bit/pixel (8 bit/component) signals were transmitted.
The maximum cable distance depends on the connected devices. The distance may not be extended with some device combinations, cabling method, or other manufacturer’s
cable. Video may be disturbed or may not be output even if signals are within the range mentioned above.
*7
HDBaseT input: DVI signals protected by HDCP are not supported.
To transmit those signals, use an IDK’s twisted pair cable extender supporting DVI signals.
*8
RJ-45 (HDBaseT connector) is only for extending digital video and audio signals over a Cat5e/Cat6 twisted pair cable.
Use it with IDK’s twisted pair cable transmitter or
receiver. Do not use for LAN devices.
*9
T568A or T568B straight. The CAT.5E HDC cable is developed by IDK and recommended by HDBaseT alliance.
*10
The maximum extension distance was obtained when IDK’s CAT.5E HDC cable was used.
The distance may not be extended with some device combinations, cabling method, or other manufacturer’s cable. Video may be disturbed or may not be output even if signals
are within the range mentioned above.
Operations may not be stable with some LCD devices; please check the operation beforehand or contact us.
The maximum extension
distance is the shorter distance of connected HDBaseT product or sink device’s maximum extension distance.
*11
The IDK OPF-H1000 must be connected for optical extension input and output cards.
*12
Deep Color, x.v.Color, 3D, ARC, HEC, and CEC are not supported.
*13
Please refer to SFP Specification.
*14
It is possible to connect without using the recommended polishing method, but that may cause a change of extension distance ability due to an increase in return loss.
*15
The maximum extension distance is measured under the following conditions: Fiber that is polished by a recommended method is used, there is no interconnection, and the
allowable bending radius is not exceeded.
*16
HDBaseT output: DVI signals protected by HDCP are not supported. To transmit those signals, use an IDK’s twisted pair cable receiver supporting DVI signals.
*17
Scan converter output board uses 2 of 4 channels. Channel numbers are assigned to each connector consecutively. Channel number for unused channel is reserved but not
be able to set.
*18
30 bit/pixel (10 bit/component) Deep Color is supported while x.v.Color, 3D, ARC, HEC, and CEC are not supported.
*19
1080p and 1080i are 50 Hz/59.94 Hz.