background image

28

5.3 

Plant Configuration

Configure plant?

  
No

Yes

Plant  configuration  is  related  to  shared 

resources necessary for the operation of the 

complete cascade/plant. To configure these 

select ‘Yes’ and then follow the screens.

Hydraulic Separation:

If the boiler has Hydraulic Separation from 

the intermediate or final circuits in the heating 

system, or if the boilers have a combined flue 

system then set this option to either ‘Header’ 

or ‘Plate heat exchanger’.

Hydraulic separation?

No
Header

Plate heat exchanger

Hydraulic separation?

No
Header

Plate Heat exchanger

Hydraulic separation?

Header

Plate heat exchanger

Header Thermistor:

If  the  system  has  a  header  sensor  fitted, 

combined flow, then select ‘Yes’, otherwise 

the  system  will  use  the  average  flow 

temperature of all running boilers.

Set Flue System:

If the boilers are connected into a common 

or cascade flue system then you can choose 

multiline  flue  system  where  the  minimum 

capacity of the boiler in a cascade can be 

increased in order to ensure no backflow in 

the flue system.

Set flue system

 
Standard
Multiline

Set flue system

Standard
Multiline

If the boiler cascade has a common pump 

that circulates water through all the boilers 

in  the  Cascade  the  select  the  output  of 

the  Master  boiler  that  controls  this  pump. 

Otherwise select ‘None’.

Loc’n of shared boiler pump?

  
None

PWM/0-10V ()
MFR1 ()

The following outputs can be configured for 

this function:

Loc’n of shared boiler pump?

None

PWM/0-10V ()
MFR1 ()
MFR2 ()

Loc’n of shared boiler pump?

PWM/0-10V ()
MFR1 ()
MFR2 ()
MFR3 ()

Loc’n of shared boiler pump?

MFR1 ()
MFR2 ()
MFR3 ()
MFR4 ()

Loc’n of shared boiler pump?

MFR2 ()
MFR3 ()
MFR4 ()

Loc’n of shared boiler pump?

MFR3 ()
MFR4 ()

Note:  Once  a  programmable  has  been 

selected the function will appear within the 

parenthesis  at  the  right  of  the  designated 

output name.

If the boiler cascade has a common pump 

that circulates water through either the boiler 

cascade  or  cascade  header  and  supplies 

the  heating  load  then  select  the  output  of 

the  Master  boiler  that  controls  this  pump. 

Otherwise select ‘None’.

Select Loc’n of system pump?

None

PWM/0-10V ()
MFR1 ()

The following outputs can be configured for 

this function:

Select Loc’n of system pump?

None

PWM/0-10V ()
MFR1 ()
MFR2 ()

Select Loc’n of system pump?

PWM/0-10V ()
MFR1 ()
MFR2 ()
MFR3 ()

Select Loc’n of system pump?

MFR1 ()
MFR2 ()
MFR3 ()
MFR4 ()

Select Loc’n of system pump?

MFR2 ()
MFR3 ()
MFR4 ()

Select Loc’n of system pump?

MFR3 ()
MFR4 ()

If the boiler cascade has a shunt pump to 

control  the  temperature  differential  of  the 

cascade flow to return then select the output 

of the Master boiler that controls this pump. 

Otherwise select ‘None’.

Select Loc’n of shunt pump?

None

PWM/0-10V ()
MFR1 ()

The following outputs can be configured for 

this function:

Select Loc’n of shunt pump?

None

PWM/0-10V ()
MFR1 ()
MFR2 ()

Select Loc’n of shunt pump?
PWM/0-10V ()
MFR1 ()
MFR2 ()
MFR3 ()

Select Loc’n of shunt pump?
MFR1 ()
MFR2 ()
MFR3 ()
MFR4 ()

Содержание EVOMAX 2

















































Отзывы: