Ideal Boilers Mexico Super RS4100 Скачать руководство пользователя страница 28

Страница: 28 / 36

Mexico Super RS485 - RS4125 -

Installation & Servicing

SERVICING

44 IGNITION ELECTRODE REPLACEMENT

45 MAIN BURNER REPLACEMENT

Refer to Frame 37.

Remove the 2 screws, lift off the lower front panel
then remove the grille assembly. Refer to Frame
31.

Disconnect the electrical leads from the gas valve.

Undo the gas cock union. Remove the 4 wing nuts
and withdraw the burner and controls assembly,
complete, from the boiler.

Disconnect the ignition lead from the PCB.

Prise the retaining clip out of the groove in
the electrode, using a small screwdriver,
and withdraw the electrode.

Push in the new electrode until the
retaining clip locates in the groove and
reassemble in reverse order.

Refer to Frame 37.

Remove the 2 screws,
lift off the lower front
panel then remove the
grille assembly. Refer
to Frame 31.

Disconnect the
electrical leads from
the gas valve.

Undo the gas cock
union. Remove the 4
wing nuts and
withdraw the burner
and controls assembly,
complete, from the
boiler.

Disconnect the ignition
lead from the PCB.

Remove the 2 screws
securing the pilot
burner and pull the
assembly clear of the

main burner.

Remove the 2 nuts and washers securing the burner to
the front plate and manifold. Withdraw the burner.

Fit the new burner and reassemble in reverse order,
taking care not to damage the main burner injector
which is screwed into the burner manifold.

SER

VICING

200942-1.p65

3/4/2004, 9:25 AM

Содержание Mexico Super RS4100





































Результаты поиска

Содержание Mexico Super RS4100

Отзывы:

Похожие инструкции для Mexico Super RS4100

Бренды по названию

Популярные бренды

Ideal Boilers Mexico Super RS4100, Установка и обслуживание

Результаты поиска

Содержание Mexico Super RS4100

Отзывы:

Похожие инструкции для Mexico Super RS4100

Бренды по названию

Популярные бренды