Ideal Boilers Mexico Super RS4100 Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 36

background image

14

Mexico Super RS485 - RS4125 -

Installation & Servicing

INSTALLATION

11 PREPARING THE BOILER

Note.

Before placing the boiler in the selected position any gas
and water connections at the rear of the boiler should be
prepared, due to the possible lack of access.

1.

Screw the distributor tube (supplied with a 1" BSP x
28mm copper adaptor) into the selected heating return
tapping, using an appropriate jointing material.

IMPORTANT.

It is

IMPERATIVE

that the index mark on the distributor

tube bush is in alignment with the mark on the section
boss, as shown in Frame 7.

DO NOT disturb it when connecting subsequent
pipework.

Fully pumped systems using more than 1 pump,
serving separate zones, must have a common return
connection to the distributor tube.

2.

Select the desired pumped flow tapping.

3.

Screw the supplied boiler thermostat pocket into the
appropriate front section tapping, using an approved
jointing material. Refer to Tables 7 and 8.

4.

Connect pipe fittings to the rear tappings and plug any
unused tappings.

Note

.

If using iron elbows fit a short straight connector into

the boiler tapping first, to clear the casing.

Connections - as viewed at front

Thermostat Position

Back Section

Front Section

CH

DHW

Flow Return

Flow

Return

Top

LH

LH

RH

RH

LH

LH

RH

RH

LH

LH

RH

RH

LH

LH

RH

RH

LH

LH

RH

RH

Table 8 - Gravity Domestic Hot Water
and Pumped Central Heating

Table 7 - Fully Pumped Systems

Connections - as viewed at front

Thermostat Position

Back Section

Front Section

Flow

Return

Top

LH

LH

LH

LH

RH

LH

RH

RH

RH

RH

LH

RH

12 PREPARING THE WALL

1

. Cut the appropriate hole in

the wall for insertion of the
terminal assembly.

Notes.
a.

Make good the hole on
the INSIDE of the
building to the given
dimensions BEFORE
fitting the boiler, to
facilitate sealing
between the terminal
and the wall when the
boiler is in position.

b.

The terminal MUST NOT
come into contact with a
combustible material
such as that used in non-
standard construction of
timber frame and
plasterboard etc.

Boiler

Dimension A

RS485

533 mm (21")

RS4100

533 mm (21")

RS4125

600 mm (23

5/8

")

2.

Place the boiler in the selected position.

3.

Make good the brickwork around the air duct.

INST

ALLA

TION

200942-1.p65

3/4/2004, 9:24 AM

14

«
...
12
13
14
15
16
...
»

Содержание Mexico Super RS4100





































Отзывы:

Нет отзывов

Похожие инструкции для Mexico Super RS4100

ecoVIT exclusiv VKK 226/4-H

Бренд: Vaillant Страницы: 16

Бренд: Raypak Страницы: 213

Tahiti Condensing 24 kW Combi (KC)

Бренд: Fondital Страницы: 56

Бренд: Vaillant Страницы: 80

Бренд: U.S. Boiler Company Страницы: 176

Worcester Greenstar Utility

Бренд: Bosch Страницы: 20

WORCESTER GREENSTAR DANESMOOR WALL MOUNTED OIL 12/18

Бренд: Bosch Страницы: 20

Worcester Greenstar Utility ErP+ 32/50

Бренд: Bosch Страницы: 16

Worcester Greenstar Utility 32/50

Бренд: Bosch Страницы: 48

Worcester GREENSTAR 12i System

Бренд: Bosch Страницы: 70

Бренд: Saunier Duval Страницы: 4

Бренд: IBC Страницы: 6

Бренд: Dunkirk Страницы: 36

PELLEMATIC SmartXS

Бренд: Okofen Страницы: 100

Flexible Water Tube Boilers

Бренд: Bryan Boilers Страницы: 8

Mexico Slimline CF440

Бренд: Ideal Boilers Страницы: 36

Greenstar 8000 Life GR8300iW 30 C

Бренд: Worcester Страницы: 76

Бренд: Ideal Boilers Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды