Ideal Boilers Mexico Super RS4100 Скачать руководство пользователя страница 12

Страница: 12 / 36

Mexico Super RS485 - RS4125 -

Installation & Servicing

INSTALLATION

The boiler is supplied fully assembled in Pack A,
together with either one of 3 packs:

B, B1 or C.

Packs B, B1 or C contain the flue terminal appropriate
to the wall thickness.

Unpack and check the contents.

UNPACKING

PACK 'A' CONTENTS

Complete boiler assembly

The Hardware Pack (listed separately below)

These Installation and Servicing/User
Instructions

complete
boiler
assembly

FLUE PACKS

Packs B, B1 and C contents

Flue terminal assembly

Sachet of sealing mastic - 2 off

HARDWARE PACK

Thermostat clip - 1 off

Thermostat pocket -1 off

Thermostat retaining pin - 1 off

1" BSP plugs - 5 off

1" x

1/2

" BSP reducing bush - 1 off

Distributor tube

Cable strap - 2 off

28mm Comp nut - 1 off

28mm olive - 1 off

Wall thickness

Flue

Dimension (duct length) X shown above

pack

Boiler fitted flush with wall

Boiler fitted in line with 600mm kitchen units

required

RS485

114 to 191 mm

1/2

" to 7

1/2

up to 125 mm

(up to 5")

RS4100

229 to 305 mm

(9" to 12")

163 to 242 mm

1/2

" to 9

1/2

318 to 394 mm

(12

1/2

" to 15

1/2

253 to 332 mm

(10" to 13")

RS4125

114 to 191mm (4

1/2

" to 7

1/2

229 to 305 mm (9" to 12")

318 to 394 mm (12

1/2

" to 15

1/2

Table 6. This table shows the pack required for the given wall thicknesses

INST

ALLA

TION

200942-1.p65

3/4/2004, 9:24 AM

Содержание Mexico Super RS4100





































Результаты поиска

Содержание Mexico Super RS4100

Отзывы:

Похожие инструкции для Mexico Super RS4100

Бренды по названию

Популярные бренды

Ideal Boilers Mexico Super RS4100, Установка и обслуживание

Результаты поиска

Содержание Mexico Super RS4100

Отзывы:

Похожие инструкции для Mexico Super RS4100

Бренды по названию

Популярные бренды