background image

BIA-DPC3 rev 5 

Page 40 

 

Erasing the parameter calibration. 

Press the 

MODE

 key to switch to manual state. If the control panel is locked press 

MODE

 and 

STORE

 keys at the same time to 

unlock and go into manual mode. Make sure the pump is not running and LCD is displaying:

 

 

Press the 

A STOP

 key for 30 seconds

; the control panel makes a “beep” sound, and the control panel recovers the 

default 

factory setting and the LCD displays:

 

with Pump No Calibration flashing. 

Repeat for pump B by using the 

B STOP

 key for 30 seconds. 

8.2 Switching to AUTO mode. 
 

To switch between MANUAL and AUTO mode press 

MODE

. AUTO mode automatically locks control panel.

 

Under auto state the 

control panel will run or stop the pump according to the signal from the liquid level probe or float switch. 

Note:

 under auto state, if the pump is running and user wants to stop the pump, press the 

MODE 

key to switch to manual state 

and the pump stops. 

Note:

 under auto state, if the input power is cut off and the recovers, the control panel will enter operating state after 10 

seconds countdown 

Note:

 no matter if the control panels is under auto or manual state, if the input power is cut of and recovers again, the control 

panel will resume its operation in the same state as before the power being cut off.  

8.3 Switching to MANUAL mode. 

 
To switch between AUTO and MANUAL model press 

MODE

 and 

STORE

 keys at the same time to unlock and go into MANUAL 

mode.

 

Press the 

START

 key to start the pump and the 

STOP

 to stop the pump.

 

4.4 Alarm Test. 

 
Under MANUAL mode and pump/s not operating press 

STORE

 for 3 seconds to test the alarm. 

 

8.5 Pump Protection 

During pump running, if dry run, overload, over voltage, etc failures occur, the control panel will immediately shut down the 
pump running and automatically execute a check for restarting conditions after a built in time delay has elapsed. The control 
panel will not recover automatically until all the abnormal situations have been cleared. 

If pump stalled, open phase or other serious failure has occurred, pump user must immediately check pump and motor. 

 

 

 

Содержание DPC3















































Отзывы: