background image

BIA-DPC3 rev 5 

Page 14 

 

Conventions used in this manual. 

In the manual the following symbols will be used: 

Generic danger. Failure to comply with the safety regulations that follow can irreparably damage the 

controller or equipment. 

 Electric shock risk. Failure to comply with the safety regulations that follow can cause death or serious injury. 

WARNINGS 

Read this manual carefully before any operation. 

Please keep this manual for future use. 

WARNING!! 

1.

 

Installation must be carried out by a suitably qualified electrician. 

2.

 

Before carrying out any installation or maintenance operation, controller must be disconnected from the 
power supply. 

3.

 

Do not open the cover during running the controller. 

4.

 

Do not splash water or other liquid over the controller. 

5.

 

Do not allow children or infirm persons to operate the control. 

6.

 

Qualified electrician is to correctly size and install circuit breakers to protect power supply. 

CAUTION!! 

1.

 

The electrical and hydraulic connections must be carried out by competent, skilled, qualified personnel. 

2.

 

Never connect AC power to the output terminals. 

3.

 

Ensure the pump and controller characteristics match. 

4.

 

Do not install the controller in the following conditions: 

a.

 

Vibration and mechanical shock. 

b.

 

Corrosive gasses and liquids. 

c.

 

Extreme heat and cold, operating range -25

o

C - +55

o

C. 

d.

 

Salt mist corrosion. 

e.

 

Rain and moisture. 

f.

 

Flammable materials, solvents. 

 
 
 
 
 
 

Содержание DPC3















































Отзывы: