Icom IC-M220 Скачать руководство пользователя страница 47

Страница: 47 / 66

DIGITAL SELECTIVE CALLING (DSC)

Alarm Status

Sets the alarm ON or OFF when receiving

each type of DSC call.

Safety

Routine

Warning

Sets the alarm for when:

•No MMSI code is entered.

•The position data has not been received

for 2 minutes after turning ON the

transceiver.

•The received position data has not been

updated for 10 minutes.

•The received position data has not been

updated for 4 hours.

•The manually entered position data has

not been updated for 23.5 hours.

Self-Terminate

An alarm sounds when duplicate

Distress calls are received.

Discrete

An alarm sounds when a lower priority

call is received while receiving a high

priority call.

CH 70 SQL Level

Sets the Squelch level for Channel 70 to

1 ~ 10 or Open.

Self-Test

The Self-Test sends DSC signals to

the receiving AF circuit to compare the

sending and receiving signals at the AF

level.

Push [ENT] to start the Self-Test.

When the sending and receiving DSC

signals match, “OK” is displayed.

Procedure

(For only the USA version)

You can select the type of task for the

transceiver, depending on the presetting.

Single: Handles only 1 task at the same

time.

Multiple: Handles up to 7 tasks at the

same time.

Содержание IC-M220



































































Результаты поиска

Содержание IC-M220

Отзывы:

Бренды по названию

Популярные бренды

Icom IC-M220, Инструкция по эксплуатации

Результаты поиска

Содержание IC-M220

Отзывы:

Бренды по названию

Популярные бренды