Icom IC-M220 Скачать руководство пользователя страница 19

Страница: 19 / 66

BASIC OPERATION

■

Adjusting the volume level

1. Push [VOL].

•

The volume adjustment screen is displayed.

2. Push [▲], [▼], [◄], or [►] to adjust the audio volume

level.

If no key is pushed for 5 seconds, the screen

automatically closes.

■

Adjusting the squelch level

Squelch enables the audio to be heard only while receiving a signal that is stronger than

the set level. A higher level blocks weak signals, so that you can receive only stronger

signals. A lower level enables you to hear weak signals.

1. Push [VOL] twice.

•

The squelch level adjustment screen is displayed.

2. Push [▲], [▼], [◄], or [►] to adjust the squelch level.

If no key is pushed for 5 seconds, the screen

automatically closes.

■

Adjusting the backlight or the display contrast

1. Open the “BACKLIGHT” or “CONTRAST” screen.

[MENU] > Configuration >

Backlight

[MENU] > Configuration >

Display Contrast

2. Push [▲], [▼], [◄], or [►] to adjust, and then push

[ENT] to set.

Push

EXIT

to exit the Menu screen.

Содержание IC-M220



































































Результаты поиска

Содержание IC-M220

Отзывы:

Похожие инструкции для IC-M220

Бренды по названию

Популярные бренды

Icom IC-M220, Инструкция по эксплуатации

Результаты поиска

Содержание IC-M220

Отзывы:

Похожие инструкции для IC-M220

Бренды по названию

Популярные бренды