Icom IC-M220 Скачать руководство пользователя страница 24

Страница: 24 / 66

DUALWATCH/TRI-WATCH

■

Description

Dualwatch and Tri-watch are convenient to periodically check Channel 16 while you are

operating on another channel.

When a signal is received:

On Channel 16:

Dualwatch/Tri-watch pauses on Channel 16 until the signal

disappears.

On the Call channel:

Tri-watch switches to Dualwatch until the signal on the Call

channel disappears.

■

Operation

1. Select Dualwatch or Tri-watch on the Menu screen.

[MENU] > Radio Settings >

Dual/Tri-Watch

2. Push [▲] or [▼] to select a channel.

3. Push [◄] or [►] to display

(Dualwatch) or

(Tri-watch).

4. Push

•

Dualwatch or Tri-watch starts.

•

“

” is displayed for Dualwatch, or “

” is

displayed for Tri-watch.

“

” is displayed when a signal is received on

the Call channel.

A beep sounds and “

” blinks when a signal is

received on Channel 16.

5. To cancel Dualwatch or Tri-watch, push

again.

CH 16

Dualwatch

Tri-watch

Operating

channel

Operating

channel

Call

channel

Periodically checks Channel

16 while operating on another

channel.

Periodically checks Channel 16 and

the Call channel while operating on

another channel.

Содержание IC-M220



































































Результаты поиска

Содержание IC-M220

Отзывы:

Похожие инструкции для IC-M220

Бренды по названию

Популярные бренды

Icom IC-M220, Инструкция по эксплуатации

Результаты поиска

Содержание IC-M220

Отзывы:

Похожие инструкции для IC-M220

Бренды по названию

Популярные бренды