Icom IC-M220 Скачать руководство пользователя страница 22

Страница: 22 / 66

SCAN OPERATION

■

Scan types

You can find ongoing communication by scanning the Favorite channels.

Before starting a scan :

•

Set the channels that you want to scan as Favorite channels. (p.

13)

Only the Favorite channels are scanned.

•

Set the scan type to “Priority Scan” or “Normal Scan” on the “Radio Settings” screen.

(p.

41)

[MENU] > Radio Settings >

Scan Type

Normal Scan

Sequentially searches through all Favorite channels. Channel 16 is not scanned unless it

is set as a Favorite channel.

CH 04

CH 02

CH 03

WX*

CH 01

CH 05

Priority Scan

* For the USA version. When the Weather

Alert function is ON, the previously

selected Weather channel is also scanned.

Sequentially searches through all Favorite channels, while also periodically checking

Channel 16.

CH 16

CH 04

CH 02

CH 03

WX*

CH 01

CH 05

When a signal is received:

On Channel 16:

The scan pauses until the signal disappears.

On a channel other than Channel 16:

The scan becomes Dualwatch until the signal

disappears.

* For the USA version. When the Weather

Alert function is ON, the previously

selected Weather channel is also scanned.

Содержание IC-M220



































































Результаты поиска

Содержание IC-M220

Отзывы:

Похожие инструкции для IC-M220

Бренды по названию

Популярные бренды

Icom IC-M220, Инструкция по эксплуатации

Результаты поиска

Содержание IC-M220

Отзывы:

Похожие инструкции для IC-M220

Бренды по названию

Популярные бренды