background image

11

54

SPECIFICATIONS

D

General

• Frequency coverage

: Receive

0.03–29.999999 MHz*

1

Transmit

1.800– 1.999999 MHz*

2

3.500– 3.999999 MHz*

2

7.000– 7.300000 MHz
10.100–10.150000 MH
14.000–14.350000 MHz
18.068–18.168000 MHz
21.000–21.450000 MHz
24.890–24.990000 MHz
28.000–29.700000 MHz

*

1

Guaranteed range: 0.5–29.999999 MHz

*

2

Varies according to version

• Mode

: USB, LSB, CW, RTTY, AM, 

• Number of memory 

: 101 

(99 regular, 2 scan edges)

channels

• Frequency stability

: Less than ±200 Hz from 1

min. to 60 min. after power
on. After that rate of stability
less than ±30 Hz/hr. at
+25°C 

(+77°F)

. Temperature

fluctuations 0°C to +50°C

(+32°F to +122°F)

less than

±350 Hz.

• Power supply 

: 13.8 V DC ±15% 

requirement

(negative ground)

• Current drain 

: Receive

(at 13.8 V DC)

Standby

1.3 A

Max. audio

2.0 A

Transmit
Max. power 20.0A

• Operatable temp. range : –10°C to +60°C; +14°F to

+140°F

• Antenna connector

: SO-239

(

50 

)

• Dimensions

: 240(W)

×

95(H)

×

239(D) mm

(projections not included)

9

7

16

(W)

×

3

3

4

(H)

×

9

13

32

(D) in

• Weight 

(approx.)

: 3.8 kg; 8 lb 6 oz

• ACC connector

: 13-pin

• REMOTE connector

: 2-conductor 3.5 (d) mm (

1

8

˝)

D

Transmitter

• Output power

:

SSB, CW, RTTY

2–100 W

AM

2–40 W

• Modulation system

:

SSB

Balanced modulation

AM

Low level modulation

• Spurious emissions

: Less than –50 dB below

peak output power

*Spurious freq.; below 30 MHz: –50 dB, above 30 MHz:

–60 dB

• Carrier suppression

: More than 40 dB

• Unwanted sideband

: More than 50 dB

• Microphone connector : 8-pin connector (600 

)

• Key connector

: 3-conductor 6.5 (d) mm (

1

4

˝)

• SEND/ALC connector : Phono (RCA)

D

Receiver

• Receive system

: Double-conversion

superheterodyne system

• Sensitivity

:

SSB, CW, RTTY

0.16 µV (1.8–29.999999 MHz)

AM

13 µV (0.5–1.799999 MHz)
2 µV (1.8–29.999999 MHz)

• Squelch sensitivity 

(threshold)

:

SSB, CW, RTTY

Less than 5.6 µV

• Selectivity

:

SSB, CW, RTTY

More than 2.1 kHz/–6 dB
Less than 4.5 kHz/–60 dB

AM

More than 6 kHz/–6 dB
Less than 20 kHz/–40 dB

• Spurious and image rejection ratio:

More than 70 dB

(1.8–29.999999 MHz)

• RIT variable range

: ±1200 Hz

• Audio output power 

: More than 2.0 W at 10% 

(at 13.8 V DC)

distortion with an 8 

load

• PHONES connector

: 3-conductor 6.35 (d) mm

(

1

4

˝)

• External SP connector : 2-conductor 3.5 (d) mm

(

1

8

˝)/8

All stated specifications are typical and subject to
change without notice or obligation.

Содержание IC-718































































Отзывы: