background image

32

5

RECEIVE AND TRANSMIT

ï

CW pitch control

The received CW audio pitch and monitored CW
audio pitch can be adjusted to suit your preferences
(300 to 900 Hz) with out changing the operating fre-
quency.

q

Push [SET] for 1 sec. to enter quick set mode.

w

Push [

UP]/[

DN] one or more times until “CW

PITCH” appears, then rotate the main dial to set
the desired pitch.

ï

CW reverse mode

The CW-R (CW Reverse) mode receives CW signals
with a reverse side CW carrier point like that of LSB
and USB modes. Use this mode when interference
signals are near the desired signal and you want to
change the interference tone.

q

Push [MODE] one or more times to select CW
mode.

w

Push [MODE] for 1 sec. to toggle between CW and
CW-R modes.

BFO

1/3 octave

Push for 1 sec.

Desired signal
(600 Hz)

CW mode (USB side)

Interference
(800 Hz)

BFO

1/2 octave

Desired signal
(600 Hz)

CW REV mode (LSB side)

Interference
(400 Hz)

MODE

ï

Electronic CW keyer

The IC-718 has an electronic keyer. Both keying
speed and weight (the ratio of dot : space : dash) can
be set in quick set mode.

• Setting the electronic keyer

q

Push [MODE] one or more times to select CW
mode.

w

While pushing and holding [SET], push [POWER]
to enter initial set mode.

e

Push [

UP]/[

DN] one or more times until “CW

PADDL” appears, then rotate the main dial to select
the paddle type.

• When “ud” is selected, the up/down switches on the mi-

crophone can be use as a paddle.

• When using up/down switches as a paddle, squeeze

keying function is not available.

r

Push [

UP]/[

DN] one or more times until “KEY

RAT” appears, then rotate the main dial to select
the desired weight.

• Key weight can be select from 2.8 to 4.5.

t

Push [

UP]/[

DN] one or more times until “KEY

SPD” appears, then rotate the main dial to select
the desired weight.

• Key weight can be select from 6 to 60.

Paddle operation from front panel MIC connector
Connect a CW paddle as at right to operate an elec-
tronic keyer from the front panel MIC connector.

• This function is available from the front panel mic con-

nector only.

• Be sure to select item “n,”“r,”or “oF” in CW PADDL in ini-

tial set mode.

• Connect straight key to “DOT” side.

This shows the 
default setting for 
the CW pitch control 
(600 Hz).

KEYING WEIGHT EXAMPLE: morse code “K”

*SPACE and DOT length can be adjusted with “KEY SPD”
  in the quick set mode only.

DASH

Weight setting:
1:1:3 (default)

Weight setting:
Adjusted

DASH

DOT

(Fixed*)

Adjustable range

SPACE (Fixed*)

front panel
MIC connector

MIC U/D

CW
paddle

DOT

E

DASH

y

3.9 k

 

±

5%

2.2 k

 

±

5%

e

Paddle operation

Содержание IC-718































































Отзывы: