Icom IC-718 Скачать руководство пользователя страница 50

Страница: 50 / 62

INSTALLATION AND CONNECTIONS

■

Opening the transceiver’s
case

Follow the case and cover opening procedures shown
here when you want to install an optional unit or adjust
an internal unit, etc.

CAUTION:

DISCONNECT the DC power cable

from the IC-718 before performing any work on the
transceiver. Otherwise, there is danger of electric
shock and/or equipment damage.

Remove the 5 screws from the top of the trans-
ceiver and 4 screws from the sides, then lift up the
top cover.

Remove the 5 screws from the bottom of the trans-
ceiver, then remove the bottom cover.

■

Optional bracket and carrying handle

Mounting bracket

An optional IC-MB5

MOBILE MOUNTING BRACKET

available to install the radio under a table, on a wall, in

a vehicle, etc.

Select an area to mount the receiver keeping in mind
that the weight of the transceiver is approx. 3.80kg.

Carrying handle

An optional handle allows you to easily carry and

transport the transceiver.

Attach the MB-23

CARRYING HANDLE

with the sup-

plied rubber feet as shown.

Содержание IC-718































































Результаты поиска

Содержание IC-718

Отзывы:

Бренды по названию

Популярные бренды

Icom IC-718, Инструкция по эксплуатации

Результаты поиска

Содержание IC-718

Отзывы:

Бренды по названию

Популярные бренды