background image

12

55

OPTIONS

AT-180 HF + 50 MHz AUTO-
MATIC ANTENNA TUNER

Fully automatic antenna tuner with
preset memories for each 100 kHz.
Unique “Automatic tuner on ” function
is available. See P. 51 for AT-180 spec-
ifications.

IC-PW1 HF + 50 MHz 1 KW LINER AMPLIFIER

Full-duty 1 kW linear am-
plifier including an auto-
matic antenna tuner. Has
automatic tuning and
band selection capability.
Full break-in (QSK) op-
eration is possible. The
amplifier/power supply
unit and the remote con-
trol unit are separated.

AH-4 HF + 50 MHz AUTOMATIC
ANTENNA TUNER

Specially designed to tune a long wire
antenna for portable or mobile HF op-
eration. The PTT tuner start function
provides simple operation.
• Input power rating: 120 W

SP-20 EXTERNAL SPEAKER

4 audio filters; headphone jack; can
connect to 2 transceivers.
• Input impedance: 8 

• Max. imput power: 5 W

HM-36 HAND MICROPHONE

Hand microphone equipped with
[UP]/[DOWN] switches.
Same as supplied.

SM-8 DESKTOP MICROPHONE

Including 2 connection cables for si-
multaneous connection of 2 trans-
ceivers. Has [UP]/[DOWN] switches.
The OPC-589 is necessary to use mi-
crophone.

AH-2b ANTENNA ELEMENT

A 2.5 m long an-
tenna element for
mobile operation
with the AH-4.
• Frequency 

coverage:
3.5–28 MHz bands
with the AH-4

SM-20 DESKTOP MICROPHONE

Unidirectional, electret microphone for
base station operation. Includes
[UP]/[DOWN] switches and a low cut
function.

SM-6 DESKTOP MICROPHONE

Electret condenser-type desktop mi-
crophone.

PS-85 DC POWER SUPPLY

Light weight switching regulator sys-
tem power supply.
• Output voltage: 13.8 V DC
• Max. current drain: 20 A

SP-21 EXTERNAL SPEAKER

Designed for base station operation.
Input impedance: 8 

Max. input power: 5 W

Содержание IC-718































































Отзывы: