background image

27

BACnet / Electric Water Heaters 

Table 22. BACnet/Electric Water Heaters Object List

BACnet  

Object Name  

(Description)

BACnet 

Object 

Type/Inst.

BACnet 

Object  

Property

R/W

Units

Min 

Value  

(if W)

Max 

Value  

(if W)

Tank Temperature

(Controlling (Tank) Temperature)

Analog Input 5

Present_Value

R

ºC

Lower Temperature 

(Lower  or Secondary Temperature)

Analog Input 4

Present_Value

R

ºC

Tank Temperature 

(Controlling Tank Temperature algorithmically 

calculated)

Analog Input 5

Present_Value

R

ºC

Temper Setpoint 

 

(Desired Tank Temperature)

Analog Value 201

Present_Value

R/W

ºC  

(ºF)

32.2 

(90)

82.2 

(180)

Differen’lBank1

 

(Differential Setpoint Bank 1)

Analog Value 202

Present_Value

R/W

°C 

(°F)

.6 

(1)

11.1 

(20)

Differen’lBank2

 

(Differential Setpoint Bank 2)

Analog Value 203

Present_Value

R/W

°C 

(°F)

.6 

(1)

11.1 

(20)

Differen’lBank3

 

(Differential Setpoint Bank 3)

Analog Value 204

Present_Value

R/W

°C 

(°F)

.6 

(1)

11.1 

(20)

Differen’lBank4

 

(Differential Setpoint Bank 4)

Analog Value 205

Present_Value

R/W

°C 

(°F)

.6 

(1)

11.1 

(20)

Differen’lBank5

 

(Differential Setpoint Bank 5)

Analog Value 206

Present_Value

R/W

°C 

(°F)

.6 

(1)

11.1 

(20)

Number of Cycles 

(Number of heating cycles)

Analog Value 209

Present_Value

R

Number

Elapsed Time 

(Time heater has been powered up in Hours 

with two place beyond the decimal)

Analog Value 210

Present_Value

R

Hours with two 

places beyond the 

decimal.

Elapsed Days 

(The number of days that the heater has been 

powered up)

Analog Value 211

Present_Value

R

Days

Elapsed Hours 

(The hours portion that the heater has been 

powered up. Use with Elapsed Days)

Analog Value 212

Present_Value

R

Hours

Heating Time 

(Time heater has been actually heating water 

in Hours with two place beyond the decimal)

Analog Value 213

Present_Value

R

Hours with two 

places beyond the 

decimal.

Heating Days 

(The amount of time in number of days heater 

has been actually heating water)

Analog Value 214

Present_Value

R

Days

Heating Hours 

(The hour’s portion of the amount of time 

heater has been actually heating water.  Use 

with Heating Days)

Analog Value 215

R

R

Hours

#CCB HW Faults

 

(CCB Hardware Fault Counter)

Analog Value 217

Present_Value

R

Number

#Model Faults 

ETH-1000 ONLY 

(Model Fault Counter)

Analog Value 218

Present_Value

R

Number

#Temp Probe Faults 

(Temperature Probe Fault Counter)

Analog Value 219

Present_Value

R

Number

#CCB Comm Faults

 

ETH-1000 only 

(Communication Fault Counter)

Analog Value 223

Present_Value

R

Number

#ECO Faults 

(High temperature Energy Cut Off switch in 

Upper temperature probe Fault Counter)

Analog Value 224

Present_Value

R

Number

#Powr Anode Flts 

(Powered Anode Alert Counter)

Analog Value 233

Present_Value

R

Number

#Element Faults  

(Element Fault Counter)

Analog Value 234

Present_Value

R

Number

#LWCO Faults  

(Low Water Cut Off Fault Counter)

Analog Value 235

Present_Value

R

Number

#Element Banks Used

 

(Number of Element Banks in Water Heater)

Analog Value 236

Present_Value

R

Number

1. Data is encoded into the 16 bits as major revision (upper 8 bits) and minor revision (lower 8 bits).

Содержание Mirius

























































Отзывы: