ICC Mirius Скачать руководство пользователя

Страница: 42 / 56

BACnet / Boilers

Table 37. Lock and Hold Codes

Code

Description

Recommended Troubleshooting of Lockout Codes

194

Invalid ignite failure response setting

Return to Configuration mode and recheck selected parameters, reverify and

reset module.

2. If fault repeats, verify electrical grounding.

3. If fault repeats, replace module.

195

Invalid ignite failure retries setting

196

Invalid ignition source setting

197

Invalid interlock open response setting

198

Invalid interlock start check setting

199

Invalid LCI enable setting

200

Invalid lightoff rate setting

201

Invalid lightoff rate proving setting

202

Invalid Main Flame Establishing Period time

203

Invalid MFEP ﬂame failure response setting

204

Invalid NTC sensor type setting

205

Invalid Outlet high limit response setting

206

Invalid Pilot Flame Establishing Period setting

207

Invalid PII enable setting

208

Invalid pilot test hold setting

209

Invalid Pilot type setting

210

Invalid Postpurge time setting

211

Invalid Power up with lockout setting

212

Invalid Preignition time setting

213

Invalid Prepurge rate setting

214

Invalid Prepurge time setting

215

Invalid Purge rate proving setting

216

Invalid Run ﬂame failure response setting

217

Invalid Run stabilization time setting

218

Invalid Stack limit enable setting

219

Invalid Stack limit response setting

220

Unconfigured Delta T limit setpoint setting

221

Unconfigured DHW high limit setpoint setting

222

Unconfigured Outlet high limit setpoint setting

223

Unconfigured Stack limit setpoint setting

224

Invalid DHW demand source setting

225

Invalid Flame threshold setting

226

Invalid Outlet high limit setpoint setting

227

Invalid DHW high limit setpoint setting

Return to Configuration mode and recheck selected parameters, reverify and

reset module.

2. If fault repeats, verify electrical grounding.

3. If fault repeats, replace module.

228

Invalid Stack limit setpoint setting

229

Invalid Modulation output setting

230

Invalid CH demand source setting

231

Invalid Delta T limit delay setting

232

Invalid Pressure sensor type setting

233

Invalid IAS closed response setting

234

Invalid Outlet high limit enable setting

235

Invalid Outlet connector type setting

236

Invalid Inlet connector type setting

237

Invalid DHW connector type setting

238

Invalid Stack connector type setting

239

Invalid S2 (J8-6) connector type setting

Содержание Mirius
























































Результаты поиска

Содержание Mirius

Отзывы:

Похожие инструкции для Mirius

Бренды по названию

Популярные бренды

ICC Mirius, Руководство по установке

Результаты поиска

Содержание Mirius

Отзывы:

Похожие инструкции для Mirius

Бренды по названию

Популярные бренды