ICC Mirius Скачать руководство пользователя страница 10

Страница: 10 / 56

MEMBRANE SWITCH STYLE DISPLAY INSTALLATION

HIGH EFFICIENCY WATER HEATER INSTALLATION

Follow the directions under general guidelines for connecting the

module to the Energy Management System and power. This

section will guide the installer on how to mount and connect the

module to the water heater.
The control box and mounting location on the water heater is on

the top of the unit behind the display module. See

Figure 20

Figure 20. Locating the Control Box

Removal of the top is not required. Use a ladder to access the top

of taller water heaters. Locate the back of the display as shown in

Figure 21

. Disconnect the RJ45 plug from the display and connect

the RJ45 plug from the split communication cord into the display

receptacle. Plug the display communication cord back into the

receptacle on the split communication cord as shown in

Figure 22

Plug the supplied wiring harness with the gateway controller into

the remaining open RJ45 port on the Split Communication cord.

Figure 21. Locating the Back of the Display

Figure 22. Reconnecting the Communication cord to the Receptacle

Next locate the upper temperature probe and exhaust switch. See

Figure 23

Position the module between the two about 1 inch from

the central burner opening. See

Figure 24

For the 500 MBTUH

model this would be next to the upper temperature probe.

Figure 23. Locating Upper Temperature Probe and Exhaust Switch

Figure 24. Connecting the Communications Cable to the Module

Connect the three wires from the end of the communication cable

to the module in accordance with

Figure 24

. Once the unit is

installed and connected, the building management system can be

connected to the appropriate connection point on the module.

COMMERCIAL ELECTRIC WATER HEATER INSTALLATION

Follow directions in

Device Configurations

(page 6

)

for connecting the

module to the Energy Management System and power. This

section will guide the installer on how to mount and connect the

module to the water heater.
The module should be located where it will not interfere with the

door or in a location that is acceptable to the customer. Care

should be exercised to avoid drilling the self tapping screws into

electrical or sensitive components. Electrical power should be

disconnected before proceeding with ICC installation.

Using a ﬂat blade screwdriver, loosen the screws holding the door

of the unit. See

Figure 25

Swing the door to the open position and locate the back of the

display module. See

Figure 26

Figure 25. Loosening the Screws to the Door of the Unit

Содержание Mirius
























































Результаты поиска

Содержание Mirius

Отзывы:

Бренды по названию

Популярные бренды

ICC Mirius, Руководство по установке

Результаты поиска

Содержание Mirius

Отзывы:

Бренды по названию

Популярные бренды