ICC Mirius Скачать руководство пользователя страница 18

Страница: 18 / 56

BACnet / Gas Water Heaters

Table 10. BACnet/Gas Water Heaters Object List

BACnet

Object Name

(Description)

BACnet

Object

Type/Inst.

BACnet

Object

Property

R/W

Units

Min

Value

(if W)

Max

Value

(if W)

Xi 1.0

Mxi

Mxi Mod% Cmd

Commands Modulation % (0%=minimum heat,

100%=rated heat). Note: It is really an upper limit.

If heater wants to command less it will.

Analog Value 207

Present_Value

R/W

100



MxiLowTempAlrmSP

(Low Temperature Alarm)

Analog Value 208

Present_Value

R/W

ºC

(ºF)

32.2

(90)

82.2

(180)



Number of Cycles

(Number of heating cycles)

Analog Value 209

Present_Value



Elapsed Time

(Time heater has been powered up in Hours with

two place beyond the decimal)

Analog Value 210

Present_Value

Hours with two

places beyond

the decimal.



Elapsed Days

(The number of days that the heater has been

powered up)

Analog Value 211

Present_Value

Days



Elapsed Hours

(The hours portion that the heater has been pow-

ered up. Use with Elapsed Days)

Analog Value 212

Present_Value

Hours



Heating Time

(Time heater has been actually heating water in

Hours with two place beyond the decimal)

Analog Value 213

Present_Value

Hours with two

places beyond

the decimal.



Heating Days

(The amount of time in number of days heater has

been actually heating water)

Analog Value 214

Present_Value

Days



Heating Hours

(The hours portion of the amount of time heater

has been actually heating water. Use with Heating

Days)

Analog Value 215

Present_Value

Hours



IgniterCurrent

(Hot Surface Igniter current in amps)

Analog Value 216

Present_Value

Amps



#CCB HW Faults

(CCB Hardware Fault Counter)

Analog Value 217

Present_Value



#Model Faults

(Model Fault Counter)

Analog Value 218

Present_Value



#Upper Temp Faults

(Upper Temperature Probe Fault Counter)

Analog Value 219

Present_Value



#Lower Temp Faults

(Lower Temperature Probe Fault Counter)

Analog Value 220

Present_Value



#Flame Probe Flt

(Flame Probe Fault Counter)

Analog Value 221

Present_Value



#Flame Status Flt

(Flame detect or not detected at proper time Fault

Counter)

Analog Value 222

Present_Value



#CCB Comm Faults

(Communication Fault Counter)

Analog Value 223

Present_Value



#ECO Faults

(High temperature Energy Cut Off switch in Upper

temperature probe Fault Counter)

Analog Value 224

Present_Value



#LowGasPress Flt

(Low Gas Pressure switch Fault Counter)

Analog Value 225

Present_Value



#Blocked In Flts

(Blocked Inlet pressure switch Fault Counter)

Analog Value 226

Present_Value



#Blocked Exhst Flt

(Blocked Exhaust Pressure & Condensate switch

Fault Counter)

Analog Value 227

Present_Value



#Ext Vent Faults

(External Vent Fault Counter)

Analog Value 228

Present_Value



#Blower Prv Flts

(Blower Prove Pressure Switch Fault Counter)

Analog Value 229

Present_Value



#Igniter Faults

(Igniter Fault Counter)

Analog Value 230

Present_Value



1. Data is encoded into the 16 bits as major revision (upper 8 bits) and minor revision (lower 8 bits).

2. Not recommended for use currently as UIM does not currently support and warning will come up as “Unknown.”

Содержание Mirius
























































Результаты поиска

Содержание Mirius

Отзывы:

Бренды по названию

Популярные бренды

ICC Mirius, Руководство по установке

Результаты поиска

Содержание Mirius

Отзывы:

Бренды по названию

Популярные бренды