ICC Mirius Скачать руководство пользователя

Страница: 37 / 56

BACnet / Boilers

Boiler Modulating Sensor Select/DHW Demand Switch

Table 36. BACnet/Boiler Modulating Sensor Select/DHW Demand Switch
Value

Response

DHW sensor

Outlet sensor

Inlet sensor

Modbus

Auto: DHW or Inlet

Auto: DHW or Outlet

Lock and Hold Codes

Table 37. Lock and Hold Codes

Code

Description

Recommended Troubleshooting of Lockout Codes

Safety Data Faults

Unconfigured safety data

New Device, complete device configuration and safety verification.

2. If fault repeats, replace module.

Waiting for safety data verification

Device in Configuration mode and safety parameters need verification and a

device needs reset to complete verification.

Configuration ended without verification, re enter configuration, verify safety

parameters and reset device to complete verification.

3. If fault repeats, replace module.

Internal Operation Errors

Internal fault: Hardware fault

Internal Fault.

1. Reset Module.

2. If fault repeats, replace module.

Internal fault: Safety Relay key feedback

error

Internal fault: Unstable power (DCDC)

output

Internal fault: Invalid processor clock

Internal fault: Safety relay drive error

Internal fault: Zero crossing not detected

Internal fault: Flame bias out of range

Internal fault: Invalid Burner control state

Internal fault: Invalid Burner control state ﬂag

Internal fault: Safety relay drive cap short

Internal fault: PII shorted to ILK

Internal fault: HFS shorted to LCI

Internal fault: Safety relay test failed due to feedback ON

Internal fault: Safety relay test failed due to safety relay

OFF

Internal fault: Safety relay test failed due to safety relay

not OFF

Internal fault: Safety relay test failed due to feedback not

Internal fault: Safety RAM write

Содержание Mirius
























































Результаты поиска

Содержание Mirius

Отзывы:

Похожие инструкции для Mirius

Бренды по названию

Популярные бренды

ICC Mirius, Руководство по установке

Результаты поиска

Содержание Mirius

Отзывы:

Похожие инструкции для Mirius

Бренды по названию

Популярные бренды