IBM TotalStorage DS300 Скачать руководство пользователя страница 65

Страница: 65 / 680

Chapter 3. Components overview

Rear view

The following sections detail the LEDs, controls and connectors for the power
supply and controller at the rear of the storage subsystem.

Power supply

Figure 3-13 shows the LEDs, controls and connectors on the power supply.

Figure 3-13 DS400 power supply LEDs, controls and connectors

򐂰

AC power connector - Connect the power cord to this connector.

򐂰

AC power on/off switch - Use this switch to turn the power supply on and off.

򐂰

Power OK LED (green) - When this LED is lit, it indicates that the power
supply is turned on.

򐂰

Fault LED (amber) - When this LED is lit, there is a fault with either the power
supply or a fan.

Table 3-8 Power supply LEDs

Power supply problem Indicator

Action

Green Power Supply Power LED is off.

Verify that the power cord is plugged in and that the
storage subsystem power is on.

Содержание TotalStorage DS300








































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание TotalStorage DS300

Отзывы:

IBM TotalStorage DS300, Руководство по лучшим практикам, Страница: 65 / 680

Результаты поиска

Содержание TotalStorage DS300

Отзывы: