manualshive.com logo in svg

IBM TotalStorage DS300, Руководство по лучшим практикам, Страница: 211 / 680

Поделиться
Скачать
IBM TotalStorage DS300 Скачать руководство пользователя страница 211

 Chapter 4. TotalStorage DS300 and DS400 management 

193

Installable Edition, needs to be installed first before it can be used. A start menu 
entry is created to run the utility. For more details about DSA and the download 
see the URL below. This book assumes that the DSA Portable Edition is used.

Link of DSA:

http://www-1.ibm.com/servers/eserver/xseries/systems_management/dsa.html

DSA can be executed with options. The order of the options are important. First 
are all options for the installer specified. To use options for the DSA itself, specify 
/a followed by those options. A few important options are:

/s

accept the license, option is for the installer

/a

option for the installer to pass all remaining options to DSA

/v

DSA option to create HTML output files

More about the options are documented in the readme file of DSA which can be 
downloaded together with the appropriate DSA edition.

Download the DSA portable edition and store the file on all systems attached to 
the IBM TotalStorage DS300 and IBM TotalStorage DS300. Perform the following 
steps to gather information about the system:

1. Click Start

→

 Run. In the Run window select the DSA executable.

Figure 4-185   Run — DSA installer 

2. Add the option /a /v behind the executable. then click 

OK

.

Содержание TotalStorage DS300









































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов