IBM TotalStorage DS300 Скачать руководство пользователя страница 102 | Manualshive

Страница: 102 / 680

IBM TotalStorage DS300 Скачать руководство пользователя страница 102

84

IBM TotalStorage DS300 and DS400 Best Practices Guide

Figure 4-10 Configure ETH2[B}

7. Set the IP address, subnet mask and broadcast address for the second iSCSI

interface of controller A ETH3[A].

DS300-1[A]# interface manage eth2[B] ip 192.168.1.62
Please wait.

Interface values are now:
    IP address: 192.168.1.62
Broadcast address: 192.168.1.255
    Netmask: 255.255.255.0

DS300-1[A]# interface manage eth2[B] netmask 255.255.255.192
Please wait.

Interface values are now:
    IP address: 192.168.1.62
Broadcast address: 192.168.1.255
    Netmask: 255.255.255.192

DS300-1[A]# interface manage eth2[B] broadcast 192.168.1.63
Please wait.

Interface values are now:
    IP address: 192.168.1.62
Broadcast address: 192.168.1.63
    Netmask: 255.255.255.192

DS300-1[A]#

«
...
100
101
102
103
104
...
»

Содержание TotalStorage DS300









































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов