IBM TotalStorage DS300 Скачать руководство пользователя страница 471

Страница: 471 / 680

Chapter 9. TotalStorage DS400 installation

453

3. Disable the access of the second HBA with alias

RIOGRANDE-S4-(1)

to any

port.

Figure 9-4 Disable initiator access

4. To be able to install onto the logical drive on the DS400, one port must allow

access for an initiator. The port used is A0. A1, B0 and B1 will be deactivated
for the first HBA.

Figure 9-5 Disable initiator access for certain ports

5. Verify that only one port is enabled for only one HBA. Only port A0 allows

access for the first HBA.

DS400[A]# initiator manage RIOGRANDE-S4-(1) deny all
Access denied to initiator RIOGRANDE-S4-(1) on all ports

DS400[A]#

DS400[A]# initiator manage RIOGRANDE-S3-(0) deny A1 B0 B1
Access denied to initiator RIOGRANDE-S3-(0) on ports A1 B0 and B1

DS400[A]#

Содержание TotalStorage DS300








































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание TotalStorage DS300

Отзывы:

IBM TotalStorage DS300, Руководство по лучшим практикам, Страница: 471 / 680

Результаты поиска

Содержание TotalStorage DS300

Отзывы: