manualshive.com logo in svg

IBM TotalStorage DS300, Руководство по лучшим практикам, Страница: 566 / 680

Поделиться
Скачать
IBM TotalStorage DS300 Скачать руководство пользователя страница 566

548

 

IBM TotalStorage DS300 and DS400 Best Practices Guide

Figure 9-147   Multipath disk device properties 

9.2.9  Finish the IBM TotalStorage DS4000 FC2-133 Host Bus Adapter 
BIOS setup

During the initial setup of the host bus adapter, only one boot device was defined.

To insure that the system boot can take place no matter which controller owns 
the array of the boot logical drive, the alternate controller must be defined as a 
boot target. The appropriate LUN must be selected as well. This settings needs 
to be defined also for the second host bus adapter to allow booting the system in 
case the first HBA fails. This will not be the case under all circumstances. There 
is no failover driver available, so it depends on the kind of problem if the system 
can use the second host bus adapter to boot from.

1. Reboot the system. During POST press 

CTRL+Q

 when the adapter displays 

the message “Press <CTRL+Q> for Fast!UTIL” to enter the host bus adapter 
BIOS setup.

Содержание TotalStorage DS300









































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов