manualshive.com logo in svg

IBM TotalStorage DS300, Руководство по лучшим практикам, Страница: 279 / 680

Поделиться
Скачать
IBM TotalStorage DS300 Скачать руководство пользователя страница 279

 Chapter 7. TotalStorage DS300 installation 

261

The second port does not see any devices because there are no devices 
configured for this port. This will be done in the next steps.

7.1.10  Configure iSCSI host bus adapter firmware settings

There are two settings which need to be changed in the iSCSI host bus adapter 
firmware. These settings are the same for the IBM iSCSI Server Adapter and the 
QLogic iSCSI Expansion Card for IBM

^

 BladeCenter and are required 

for the IP failover of the DS300 controllers. These are:

򐂰

ARP Redirect — set to enable

򐂰

Connection keep alive time-out — set to 180 (was 30)

To change these firmware settings perform the following steps:

1. From the SANsurfer utility select on the 

iSCSI HBA

 tab the first port of the 

iSCSI host bus adapter. Click the 

Port Options

 tab. On the Port options tab is 

a 

Firmware

 tab. Click the firmware tab. Click the 

Open

 button to edit 

Configured Firmware Values

.

Figure 7-55   Select the port of the iSCSI adapter 

Содержание TotalStorage DS300









































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов