IBM LS20 - BladeCenter - 8850 Скачать руководство пользователя

Страница: 32 / 116

The BMC log indicates an assertion event when an event has occurred. It indicates
a deassertion event when the event is no longer occurring.

Some of the error codes and messages in the BMC log are abbreviated.

You can view the contents of the BMC log from the Configuration/Setup Utility
program and from the diagnostic programs.

When troubleshooting PCI-X slots, note that the error logs report the PCI-X buses
numerically. The numerical assignments vary depending on the configuration. You
can check the assignments by running the Configuration/Setup Utility program (see
the

Installation and User’s Guide

for more information).

Viewing the BMC log from the Configuration/Setup Utility
program

For complete information about using the Configuration/Setup Utility program, see
the

Installation and User’s Guide

To view the BMC log, complete the following steps:

1. Turn on the server.

2. When the prompt

Press F1 for Configuration/Setup

appears, press F1. If you

have set a power-on password, you must type the password and press Enter to
start the Configuration/Setup Utility program.

3. Select

Advanced Settings

, select

Baseboard Management Controller (BMC)

settings

, and then select

BMC System Event Log

Viewing the BMC log from the diagnostic programs

The BMC log contains the same information whether it is viewed from the
Configuration/Setup Utility program or from the diagnostic programs.

For information about using the diagnostic programs, see “Running the diagnostic
programs” on page 43.

To view the BMC log, complete the following steps:

1. If the blade server is running, turn off the blade server.

2. Turn on the blade server.

3. When the prompt

F2 for Diagnostics

appears, press F2.

4. From the top of the screen, select

Hardware Info

5. From the list, select

BMC Log

For complete information about using the Configuration/Setup Utility program, see
the

Installation and User’s Guide

AMD Opteron LS20 Type 8850 for IBM BladeCenter: Problem Determination and Service Guide

Содержание LS20 - BladeCenter - 8850





















































































































Результаты поиска

Содержание LS20 - BladeCenter - 8850

Отзывы:

Похожие инструкции для LS20 - BladeCenter - 8850

Бренды по названию

Популярные бренды

IBM LS20 - BladeCenter - 8850, Руководство по обслуживанию

Результаты поиска

Содержание LS20 - BladeCenter - 8850

Отзывы:

Похожие инструкции для LS20 - BladeCenter - 8850

Бренды по названию

Популярные бренды