IBM Infoprint 1130 Скачать руководство пользователя | Manualshive

Страница: 185 / 433

background image

3-20

Service Manual

IBM Infoprint 1130/1140

The multipurpose tray and the envelope feeder do not have a paper
low sensor. The multipurpose tray does not have a pass thru sensor.

The following tray sensors are supported by this test:

Output Bin - Feed to all Bins Test

This test can be used to verify that the printer can feed media to the
standard bin or any installed output options. No information will be
printed on the test pages as the printhead is not turned on during the
feed test.

To run the Feed to all Bins Test:

1. Select Feed to all Bins Test from the Menu.

2. The media feeds from the default paper source.

3. The printer feeds a separate piece of media to the standard bin

first, then it feeds a separate piece of media to each output bin
installed in the following order:
First Sheet: Standard Bin, Second Sheet: Bin #1, Third Sheet:
Bin #2, Fourth Sheet: Bin #3, Fifth Sheet: Bin #4, Sixth Sheet:
Bin #5, Seventh Sheet: Bin #6, Eighth Sheet: Bin #7, Ninth
Sheet: Bin #8, Tenth Sheet: Bin #9, Eleventh Sheet: Bin #10,

Source

Tray Empty
Sensor

Paper Low
Sensor

Pass Thru
Sensor

Tray 1

YES

YES

NO

Tray 2

YES

YES

YES

Tray 3

YES

YES

YES

Tray 4

YES

YES

YES

Tray 5

YES

YES

YES

Multipurpose
Tray

YES

NO

NO

Envelope Feeder

YES

NO

YES

«
...
183
184
185
186
187
...
»

Содержание Infoprint 1130


















































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Infoprint 1130

Бренд: SPRT Страницы: 28

Бренд: EasyThreed Страницы: 4

Бренд: EASYPRINT Страницы: 37

Бренд: 3Doodler Страницы: 8

Бренд: Xante Страницы: 25

Бренд: Oki Страницы: 20

MC560 MFP CX2032

Бренд: Oki Страницы: 247

Бренд: Lexmark Страницы: 2

mobile pro advance

Бренд: AM TECH Страницы: 16

Бренд: Xerox Страницы: 150

DocuPrint C3300 DX

Бренд: Xerox Страницы: 200

Бренд: Xiamen Hanin Electronic Technology Страницы: 27

Бренд: LaserLine Страницы: 14

Бренд: Telpar Страницы: 25

Бренд: VASTEX Страницы: 8

Бренд: Brady Страницы: 48

ECP- Magenta Toner Premix/Concentrate for ECP 42

Бренд: Xerox Страницы: 2

Бренд: Oki Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды