IBM Infoprint 1130 Скачать руководство пользователя страница 205 | Manualshive

Страница: 205 / 433

IBM Infoprint 1130 Скачать руководство пользователя страница 205

3-40

Service Manual

IBM Infoprint 1130/1140

Paper Feed Jams

Paper Jams - Base Printer

Error Message 200 - Paper Jam - Remove Cartridge

This message indicates that paper is jammed at the printer input
sensor. This can be caused by the paper jamming prior to activating
the input sensor flag, the sensor not detecting paper over the
sensor, or paper arriving at the sensor too late.

Note: A defective system board or printhead can also cause a 200-
Paper Jam message to occur prior to the paper reaching the input
sensor flag. This error can display due to a problem with the HSYNC
signal to or in the printhead. Use the sub error code table to assist in
isolating a 200 paper jam message.

Note: When the StapleSmart Finisher option is installed, a
secondary message may be displayed which advises whether or not
to remove the job from the finisher. If a job has accumulated in the
finisher, then the printer alternately flashes the primary and
secondary messages to indicate that all accumulated sheets should
not be removed during the jam clearance procedure. If the sheets
are removed, then the printer does not reprint these sheets.

Error Message 201 - Paper Jam - Remove Cartridge

This message indicates the paper is jammed between the printer
input and exit sensors. This condition can be caused by the paper
exiting the input sensor too late or jamming in the fuser assembly
prior to activating the exit sensor flag in time or not at all.

Note: When the StapleSmart Finisher option is installed, a
secondary message may be displayed which advises whether or not
to remove the job from the finisher. If a job has accumulated in the
finisher, then the printer alternately flashes the primary and
secondary messages to indicate that all accumulated sheets should
not be removed during the jam clearance procedure. If the sheets
are removed, then the printer does not reprint these sheets.

«
...
203
204
205
206
207
...
»

Содержание Infoprint 1130


















































































































































































































































































































































































































































Отзывы:

Нет отзывов