IBM Infoprint 1130 Скачать руководство пользователя страница 67 | Manualshive

Страница: 67 / 433

background image

2-40

Service Manual

IBM Infoprint 1130/1140

The messages in the following table can occur in two ways. The
specified device could have been removed from the printer, for
instance to clear a paper jam. Otherwise, the device can still be
attached to the printer, but is experiencing a communications
problem, not fully connected, or having a hardware failure.

•

If the device is temporarily removed or not connected properly,
then reattach it. When the option is recognized, the printer
automatically clears the error and continues.

•

If the option is experiencing a hardware problem, turn the
printer off and back on. If the error occurs again, turn the printer
off, remove the option and call for service.

User Status Message

Explanation

Turn Printer OFF to
Enable Option

This message displays when a printer option,
Input Tray, Output Bin or Envelope Feeder, has
been attached while the printer is powered On. To
use the option, the printer must first be powered
off and back on again. Data loss results if print
jobs are active when the printer is power cycled. If
a print job is active, then remove the option and
finish the job. The printer automatically clears the
message once the option is removed. Once the
job is complete, turn off the printer and attach the
option again.

Insert Duplex Front
Cover

This message displays when the duplex front
access cover is not installed.

Close Duplex Rear Door

This message displays when the duplex rear door
is open.

«
...
65
66
67
68
69
...
»

Содержание Infoprint 1130


















































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Infoprint 1130

Бренд: Xyron Страницы: 6

Бренд: Xerox Страницы: 2

Бренд: Xerox Страницы: 40

Бренд: Xerox Страницы: 69

Бренд: Xerox Страницы: 42

WorkCentre 7232

Бренд: Xerox Страницы: 13

CX PRINT SERVER 550

Бренд: Xerox Страницы: 166

Бренд: Xerox Страницы: 4

imagePROGRAF GP-540

Бренд: Canon Страницы: 82

WORKCENTRE 5755

Бренд: Xerox Страницы: 356

Бренд: Citizen Страницы: 24

Бренд: Kyocera Страницы: 44

Бренд: Konica Minolta Страницы: 150

Бренд: MF DIGITAL Страницы: 9

Бренд: Sunso Страницы: 27

DRYWISE-FIL-DRYER-175

Бренд: DRYWISE Страницы: 32

Бренд: Epson Страницы: 150

FX-980 - Impact Printer

Бренд: Epson Страницы: 27

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды