IBM Infoprint 1130 Скачать руководство пользователя страница 123 | Manualshive

Страница: 123 / 433

IBM Infoprint 1130 Скачать руководство пользователя страница 123

2-96

Service Manual

IBM Infoprint 1130/1140

No indication that Bin X is full OR No indication that Bin X is near
full

High-Capacity Output Stacker Service Check

Service Tip: The majority of the mechanical components can be
observed during operation by removing the left, right and front
covers. The high capacity output stacker option functions without the
covers installed.

Determine which paper path stacker assembly is not functioning
properly.

Make sure the option(s) are installed correctly and the machine is
configured correctly before attempting to service the high-capacity
output stacker option.

Go to

“High-Capacity Output Stacker Board” on page 5-14

to

identify the correct jumper location at J6 for the upper and lower
units.

FRU

Action

1

Dual Output Bin X Sensor
Assembly
Control Board

Check for correct installation of
the sensor cable at J5 on the
control board. If either the Bin Full
(F) or Bin Near Full (NF) fail the
sensor test then check the voltage
at J5-3 and J5-4. The voltage
measures approxi5 V dc.
If the voltage is incorrect, replace
the control board. If correct,
replace the sensor assembly.

«
...
121
122
123
124
125
...
»

Содержание Infoprint 1130


















































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды