![background image](http://html1.mh-extra.com/html/ibm/ic35l020-deskstar-20-gb-hard-drive/ic35l020-deskstar-20-gb-hard-drive_specifications_3938692106.webp)
13.13.3 Recovered read errors
When a read operation for a sector has failed once and then has recovered at the specific ERP step, this
sector of data is reallocated automatically. A media verification sequence may be run prior to the
relocation according to the predefined conditions.
13.14 Power-Up In Standby feature set
The Power-Up In Standby feature set allows devices to be powered-up into the Standby power
management state to minimize inrush current at power-up and to allow the host to sequence the spin-up
of devices.
This feature set will be enabled/disabled via the SET FEATURES command or use of jumper. When
enabled by a jumper, the feature set shall not be disabled via the SET FEATURES command. The
enabling of this feature set shall be persistent after power cycle.
A device needs a SET FEATURES subcommand to spin-up to active state when the device has powered
up into Standby. The device remains in Standby until the SET FEATURES subcommand is received.
If power-up into Standby is enabled, when an IDENTIFY DEVICE is received while the device is in
Standby as a result of powering up into Standby, the device shall set word 0 bit 2 to one to indicate that
the response is incomplete, then only words 0 and 2 are correctly reported.
The IDENTIFY DEVICE information indicates the states as follows:
y
identify device information is complete or incomplete
y
this feature set is implemented
y
this feature set is enabled or disabled
y
the device needs the Set Features command to spin-up into active state
13.15
Advanced Power Management feature set (APM)
This feature allows the host to select an advanced power management level. The advanced power
management level is a scale from the lowest power consumption setting of 01h to the maximum
performance level of FEh. Device performance may increase with increasing advanced power
management levels. Device power consumption may increase with increasing advanced power
management levels. The advanced power management levels contain discrete bands described in the
section on Set Feature command in detail. This feature set uses the following functions:
1.
A SET FEATURES subcommand to enable Advanced Power Management.
2.
A SET FEATURES subcommand to disable Advanced Power Management.
Advanced Power Management, Automatic Acoustic Management, and the Standby timer setting are
independent functions. The device shall enter Standby mode if any of the following are true:
1.
The Standby timer has been set and times out.
2.
Automatic Power Management is enabled, and the associated algorithm indicates that the Standby
mode should be entered to save power.
3.
Automatic Acoustic Management is enabled, and the associated algorithm indicates that the
Standby mode should be entered to reduce acoustical emanations.
The IDENTIFY DEVICE response word 83, bit 3 indicates that Advanced Power Management feature is
supported if set. Word 86, bit 3 indicates that Advanced Power Management is enabled if set. Word 91,
bits 7–0 contains the current Advanced Power Management level if it is enabled.
Deskstar 60 GXP Hard disk drive specification
92
Содержание IC35L020 - Deskstar 20 GB Hard Drive
