background image

򔻐򗗠򙳰

System Storage EXP5060 Quick Start Guide

This

Quick Start Guide

describes the basic procedure for installing, cabling, and configuring the IBM

®

System Storage

EXP5060 storage expansion enclosure.

Related documentation

For detailed information about the storage expansion enclosure, see the

IBM System Storage EXP5060

Storage Expansion Enclosure Installation, User’s, and Maintenance Guide

. For safety information, see the

multilingual

IBM Safety Information

document on the

Documentation

CD.

For more information about how to use a lift tool to install the storage expansion enclosure, see the
documentation that came with your lift tool.

For educational information about the EXP5060 and other IBM System Storage products, go to
http://ibmdsseriestraining.com/. For the latest information about IBM System Storage disk storage
systems, go to http://www.ibm.com/systems/support/storage/disk.

Installation overview

The installation of the storage expansion enclosure involves the following procedures:

1.

“Installation guidelines”

2.

“Ordering the lift tool” on page 3

3.

“Unpacking the shipping box” on page 4

4.

“Installing the support rails and rear brackets” on page 7

5.

“Installing and removing the handles” on page 9

6.

“Installing the storage expansion enclosure in the rack cabinet” on page 10

7.

“Installing the DDMs” on page 12

8.

“Installing the cables” on page 14

9.

“Turning on the power” on page 19

10.

“Installing the software” on page 20

11.

“Obtaining information from the IBM Support Web site” on page 20

12.

“Updating the storage subsystem controller firmware” on page 20

13.

“Updating the storage expansion enclosure firmware” on page 20

Installation guidelines

Before you install the storage expansion enclosure in a rack cabinet, review the following guidelines:

v

This product is to be installed and serviced only by qualified IBM service representatives.

v

Because of the size and weight of the storage enclosure as shipped, a lift tool and a minimum of two
trained service technicians are required to push the enclosure out of its custom-designed package and
onto the lift tool.

v

The storage expansion enclosure must not be installed in a rack position where the top of the unit is
above 32U or the bottom of the unit is above the 29U mark on the rack cabinet.

v

Make sure that the room air temperature is below 25°C (77°F). The operating temperature for optimal
performance is 22°C (72°F) or lower.

v

Do not block any air vents; usually 15 cm (6 in.) of space provides proper airflow.

Содержание EXP5060

























Отзывы: