IBM 7208-341 Скачать руководство пользователя страница 59

Страница: 59 / 66

B.0 Appendix B. Fault Symptom Codes and Error Recovery Procedure Numbers

Use Figure 18 to resolve error messages that appear on the LCD of the 7208 Tape Drive Model 341:

1. Determine the fault symptom code (FSC) in the error message (the first two digits in the message). For example, in error message

ERR 1: AD 58 C0, the FSC is AD.

2. Locate the FSC in Figure 18 and identify the error recovery procedure (ERP) number for that FSC.

3. Locate the ERP number in Figure 19 in topic C.0, and identify the recommended error recovery procedure.

+------------------------------------------------------------------------+

¦ Figure 18. Fault Symptom Codes (FSC) and Error Recovery Procedure ¦

¦ (ERP) Numbers ¦

+------------------------------------------------------------------------¦

¦ FSC ¦ Description ¦ ERP ¦ Cause ¦

¦ ¦ ¦ Number ¦ ¦

+-----------+------------------------------------+-----------+-----------¦

¦ 02 ¦ Invalid position for WRITE ¦ 2 ¦ - ¦

+-----------+------------------------------------+-----------+-----------¦

¦ 03 ¦ Tape is write protected for WRITE ¦ 5 ¦ - ¦

+-----------+------------------------------------+-----------+-----------¦

¦ 04 ¦ LEOT encountered on current WRITE ¦ 10 ¦ - ¦

+-----------+------------------------------------+-----------+-----------¦

¦ 05 ¦ Operation has aborted (as ¦ 11 ¦ - ¦

¦ ¦ requested) ¦ ¦ ¦

+-----------+------------------------------------+-----------+-----------¦

¦ 06 ¦ LEOT encountered on the last WRITE ¦ 10 ¦ - ¦

+-----------+------------------------------------+-----------+-----------¦

¦ 08 ¦ Compression data integrity check ¦ 12 ¦ 100% ¦

¦ ¦ failed ¦ ¦ ¦

+-----------+------------------------------------+-----------+-----------¦

¦ 09 ¦ Detected LEOT during READ ¦ 10 ¦ - ¦

+-----------+------------------------------------+-----------+-----------¦

¦ 0A ¦ Length mismatch on READ ¦ 15 ¦ - ¦

+-----------+------------------------------------+-----------+-----------¦

¦ 0B ¦ Uncorrectable block on READ ¦ 8,6 ¦ T = 90% ¦

¦ ¦ ¦ ¦ D = 10% ¦

+-----------+------------------------------------+-----------+-----------¦

¦ 0C ¦ EOD encountered on READ ¦ 13 ¦ - ¦

+-----------+------------------------------------+-----------+-----------¦

¦ 0D ¦ Filemark encountered during a READ ¦ 10 ¦ - ¦

+-----------+------------------------------------+-----------+-----------¦

¦ 0E ¦ Illegal condition for READ ¦ 2 ¦ - ¦

+-----------+------------------------------------+-----------+-----------¦

¦ 0F ¦ READ issued at blank tape ¦ 4 ¦ - ¦

+-----------+------------------------------------+-----------+-----------¦

¦ 10 ¦ READ operation has aborted (as ¦ 11 ¦ - ¦

¦ ¦ requested) ¦ ¦ ¦

+-----------+------------------------------------+-----------+-----------¦

¦ 11 ¦ Too many permanent READ errors, ¦ 8,6 ¦ T = 90% ¦

¦ ¦ cannot sync ¦ ¦ D = 10% ¦

+-----------+------------------------------------+-----------+-----------¦

¦ 14 ¦ PEOT or PEOP encountered on a READ ¦ 2,8,6 ¦ - ¦

¦ ¦ or VERIFY ¦ ¦ ¦

+-----------+------------------------------------+-----------+-----------¦

¦ 15 ¦ Bad filemark encountered during a ¦ 8,6 ¦ T = 100% ¦

¦ ¦ READ ¦ ¦ ¦

+-----------+------------------------------------+-----------+-----------¦

¦ 16 ¦ Medium error detected during a ¦ 8,6 ¦ T = 90% ¦

¦ ¦ READ ¦ ¦ D = 10% ¦

+-----------+------------------------------------+-----------+-----------¦

¦ 17 ¦ Hardware error during a READ ¦ 12 ¦ D = 100% ¦

+-----------+------------------------------------+-----------+-----------¦

¦ 18 ¦ READ decompression failed - HW ¦ 12 ¦ D = 100% ¦

¦ ¦ error ¦ ¦ ¦

+-----------+------------------------------------+-----------+-----------¦

¦ 19 ¦ READ decompression CRC failed ¦ 12 ¦ D = 100% ¦

+-----------+------------------------------------+-----------+-----------¦

¦ 1C ¦ Unknown or incompatible format ¦ 14 ¦ T = 100% ¦

+-----------+------------------------------------+-----------+-----------¦

¦ 1D ¦ Hit setmark on READ ¦ 10 ¦ - ¦

+-----------+------------------------------------+-----------+-----------¦

¦ 26 ¦ Not at legal place to WFM ¦ 2 ¦ - ¦

+-----------+------------------------------------+-----------+-----------¦

¦ 27 ¦ Tape is write protected for WFM ¦ 5 ¦ - ¦

+-----------+------------------------------------+-----------+-----------¦

¦ 28 ¦ LEOT encountered during WFM ¦ 10 ¦ - ¦

+-----------+------------------------------------+-----------+-----------¦

¦ 31 ¦ Setmark detected on SPACE/LOCATE ¦ 10 ¦ - ¦

+-----------+------------------------------------+-----------+-----------¦

¦ 32 ¦ Filemark detected during ¦ 10 ¦ - ¦

7208 Model 341 Setup and Operator Guide

Appendix B. Fault Symptom Codes and Error Recovery Procedure Numbers

¦ Copyright IBM Corp. 1997

B.0 - 1

Содержание 7208-341



































































Результаты поиска

Содержание 7208-341

Отзывы:

Похожие инструкции для 7208-341

Бренды по названию

Популярные бренды

IBM 7208-341, Руководство по настройке и эксплуатации

Результаты поиска

Содержание 7208-341

Отзывы:

Похожие инструкции для 7208-341

Бренды по названию

Популярные бренды