IBM 7208-341 Скачать руководство пользователя страница 39

Страница: 39 / 66

3.3 Liquid Crystal Display

The 7208 Tape Drive features a liquid crystal display (LCD) ( 2 in Figure 8 in topic 3.0). The LCD provides operating and error

messages.

Figure 10 shows a list of messages that display on the LCD.

+------------------------------------------------------------------------+

¦ Figure 10. LCD Messages ¦

+------------------------------------------------------------------------¦

¦ Reset Messages ¦

+------------------------------------------------------------------------¦

¦ RESET ¦ The first message to appear during the ¦

¦ ¦ power-on sequence. ¦

+-----------------------+------------------------------------------------¦

¦ MODEL: ¦ Variable information about the tape drive, in ¦

¦ ¦ this case IBM--20GB ¦

+-----------------------+------------------------------------------------¦

¦ SUBMOD: ¦ The submodel number of the tape drive. ¦

+-----------------------+------------------------------------------------¦

¦ SN: ¦ The serial number of the tape drive. ¦

+-----------------------+------------------------------------------------¦

¦ CODE: ¦ The level of the tape drive's firmware. ¦

+-----------------------+------------------------------------------------¦

¦ LAST CLN: ¦ The number of hours since the last cleaning. ¦

+-----------------------+------------------------------------------------¦

¦ COMPRESSION: ¦ Whether data compression is turned on (the ¦

¦ ¦ default) or turned off. ¦

+-----------------------+------------------------------------------------¦

¦ SINGLE ENDED or ¦ The type of SCSI input/output controller ¦

¦ DIFFERENTIAL ¦ (whether single ended or differential). ¦

+-----------------------+------------------------------------------------¦

¦ WIDE ¦ The type of SCSI configuration. ¦

+-----------------------+------------------------------------------------¦

¦ SCSI ID: ¦ The SCSI address of the tape drive (0 through ¦

¦ ¦ 15). ¦

+-----------------------+------------------------------------------------¦

¦ ¦ The current language used on the LCD. To ¦

¦ ¦ change the language, power the tape drive off. ¦

¦ LANGUAGE: ¦ Press and hold the unload button immediately ¦

¦ ¦ after turning the power back on. When the ¦

¦ ¦ desired language displays, release the unload ¦

¦ ¦ button. ¦

+------------------------------------------------------------------------¦

¦ Tape Drive Status Messages ¦

+------------------------------------------------------------------------¦

¦ READY-NOTAPE ¦ The tape drive is ready to accept a cartridge. ¦

+-----------------------+------------------------------------------------¦

¦ ¦ LOADING.... ¦ The tape drive is loading the tape. ¦

+-----------------------+------------------------------------------------¦

¦ ¦ READY-TAPE ¦ The tape drive successfully loaded the tape ¦

¦ ¦ and is ready for read or write operations. ¦

+-----------------------+------------------------------------------------¦

¦ ¦ ILLEGAL TAPE ¦ An unsuitable tape has been loaded and ¦

¦ ¦ rejected. ¦

+-----------------------+------------------------------------------------¦

¦ ¦ The unload button was pressed. The tape drive ¦

¦ << EJECT====== ¦ will eject the cartridge as soon as it ¦

¦ ¦ finishes the current operation. ¦

+-----------------------+------------------------------------------------¦

¦ ¦ EJECT PREVNT ¦ The system software has issued a command to ¦

¦ ¦ prevent the eject function. ¦

+------------------------------------------------------------------------¦

¦ Tape Motion Messages ¦

+------------------------------------------------------------------------¦

¦ ¦ The tape drive is reading data. The + sign ¦

¦ ¦ appears when the data is compressed. The ¦

READ+¦¦¦¦¦= ¦ boxes (¦) represent the amount of tape ¦

¦ ¦ processed (out of a total of six boxes). The ¦

¦ ¦ = sign represents the amount of unprocessed ¦

¦ ¦ tape. ¦

+-----------------------+------------------------------------------------¦

WRITE+¦¦¦¦= ¦ The tape drive is writing data. The + sign ¦

¦ ¦ appears when the data is compressed. ¦

+-----------------------+------------------------------------------------¦

¦ / PROTECTED ¦ The tape drive cannot write data because the ¦

¦ ¦ data cartridge is write-protected. ¦

+-----------------------+------------------------------------------------¦

¦ ¦ The tape drive cannot write to the type of ¦

¦ / ILLEGAL WRT ¦ data cartridge inserted. This message remains ¦

¦ ¦ until a proper tape is inserted or a tape ¦

¦ ¦ motion command is issued. ¦

+-----------------------+------------------------------------------------¦

7208 Model 341 Setup and Operator Guide

Liquid Crystal Display

¦ Copyright IBM Corp. 1997

3.3 - 1

Содержание 7208-341



































































Результаты поиска

Содержание 7208-341

Отзывы:

Похожие инструкции для 7208-341

Бренды по названию

Популярные бренды

IBM 7208-341, Руководство по настройке и эксплуатации

Результаты поиска

Содержание 7208-341

Отзывы:

Похожие инструкции для 7208-341

Бренды по названию

Популярные бренды